Great explanation. and, I'll bet the static and popping I am hearing is the
result of my CHEAPER headphones being over driven.
So what is recommended on headphones with the Orion II?
On 4/28/06, Toby Pennington <toby423@earthlink.net> wrote:
>
> John, Here is an explanation of why your RX EQ does not behave as it did
> in
> V1 O1, for better of worse in the 2.0 firmware for both orions the RX EQ
> acts like a volume control.
>
>
>
> There is a good description of the actual operation on pages 18 and 19 of
> the manual. It does not operate as the usual bass and treble controls
> everyone is familiar with in hi-fi amplifiers. There is no set frequency
> around which they hinge to provide increased/decreased levels. So, if you
> are listening to SSB with the bandwidth set to 3kHz, setting the equalizer
> to -20 will reduce the level at approximately 100Hz by about 20dB and
> change
> the level at 3kHz by approximately -10dB. This will give you the
> impression
> that the volume has been turned down, and it has. Now increase the volume
> control and you should notice increased high frequency response and
> reduced
> bass. This is the solution to using one control and menu selection and
> adjusting both high and low frequency. This has been set in the software
> to
> operate over approximately 100Hz to 6kHz. For receive and transmit, this
> is
> independent of the bandwidth selected with filters. For example, if you
> have
> selected -20dB, you will have 20dB difference from 100Hz to 6kHz. If you
> are
> using a BW of 3000, then you get 10dB difference over the selected
> bandwidth, BW of 1000, then you get 3.33dB difference over the selected
> bandwidth. Now if the bandwidth is set to the low frequencies as you set
> the
> EQ from -20 to +20 you would notice a pronounced increase/decrease in
> gain.
>
>
>
>
>
>
> ----- Original Message -----
> From: "John Sheeley" <wb4qda@yahoo.com>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Friday, April 28, 2006 12:38 PM
> Subject: Re: [TenTec] 2.033
>
>
> > Doug
> > No raspy audio here on my Orion II . The receive EQ
> > does act kind of like a volume control the + side is
> > louder and - side is decreases the volume.
> >
> > 73
> > John WB4QDA
> >
> > --- Douglas Shock <douglas.shock@gmail.com> wrote:
> >
> > > the raspy audio on the + EQ adjust on TX or RX only
> > > occurs through the
> > > headphones.
> > >
> > > The decreased audio seems to be a function of the
> > > changes in the rec. EQ. If
> > > I adjust the RCV EQ to a pos value, the AF goes up
> > > with it. Seems like what
> > > use to be set to 0 is now 12 to 13. If I go - on the
> > > EQ it doesn't get tiny
> > > but the audio levels go down. I think this
> > > translates to the TX EQ as well.
> > >
> > > Can somebody confirm this???
> > >
> > >
> > > Doug / K0ZU
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> >
> >
> >
> > __________________________________________________
> > Do You Yahoo!?
> > Tired of spam? Yahoo! Mail has the best spam protection around
> > http://mail.yahoo.com
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|