There IS an EXT T/R Delay setting in the TX Menu but it has no effect
on the keying relay clacking.
Barry N1EU
On Mon, Nov 14, 2011 at 7:56 AM, Rick - DJ0IP / NJ0IP <Rick@dj0ip.de> wrote:
> Guys, I may be wrong, but I seem to remember that there were TWO adjustments;
> one for the relay and one for the RX recovery. It's been over 5 years since
> I have owned an Orion, but I'm pretty certain it was that way. In any case,
> it would have to be one of the items on the TX menu.
>
> 73
> Rick
>
> -----Original Message-----
> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com] On
> Behalf Of Barry N1EU
> Sent: Monday, November 14, 2011 1:40 AM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Orion's break in
>
> Correct Floyd, the CW delay makes the receiver audio quiet but does
> nothing for the relay clacking in both the Orion and Orion II.
>
> 73, Barry N1EU
>
> On Mon, Nov 14, 2011 at 12:11 AM, Floyd Sense <floyd@k8ac.net> wrote:
>> An interesting question. I wonder if the Orion and Orion 2 differ in
>> this respect. On my Orion 2, I can use the CW delay to achieve
>> semi-break-in, but I still hear the same relay clacking away. I
>> expected to hear the relay only at the beginning and end of a
>> transmission, but that's not the case - it still follows the keying,
>> although the receiver is properly muted for the delay set with the CW
>> delay function. So, maybe Toshimi's desire to eliminate the relay noise
>> is not satisfied this way.
>>
>> 73, Floyd - K8AC
>>
>>
>> On 11/13/2011 5:56 PM, Barry N1EU wrote:
>>> Menus - CW - CW QSK Delay
>>>
>>> start with 25% and increase/decrease as necessary
>>>
>>> 73,
>>> Barry N1EU
>>>
>>> On Sun, Nov 13, 2011 at 10:39 PM, Rick - DJ0IP / NJ0IP<Rick@dj0ip.de>
>>> wrote:
>>>> Hi Toshimi,
>>>>
>>>> You can adjust the delay of the TR relay.
>>>> If you select a delay, then it is effectively semi BK and no longer QSK.
>>>> This was added to the rig after the initial release so it probably was not
>>>> in the manual.
>>>> Maybe someone who owns an Orion can jump in and tell you exactly how to
>>>> adjust it. I have forgotten.
>>>>
>>>> 73
>>>> Rick, DJ0IP
>>>>
>>>> -----Original Message-----
>>>> From: tentec-bounces@contesting.com [mailto:tentec-bounces@contesting.com]
>>>> On Behalf Of Toshimi Horie
>>>> Sent: Sunday, November 13, 2011 11:32 PM
>>>> To: tentec@contesting.com
>>>> Subject: [TenTec] Orion's break in
>>>>
>>>> Hi all. I am JE2UFF.
>>>>
>>>> This month, I got the Orion of used one from US.
>>>>
>>>> I just start operation with it. I can checked user manual, but not found.
>>>>
>>>> So please tell me for everyone.
>>>> The Orion has semi break in mode? I have other rig. That's japanese one.
>>>> Normaly, japanese transceiver has two kind of break in operation mode. It's
>>>> semi and full break in.
>>>>
>>>> The Orion do the CW mode, each mores code can switch the relay. It is very
>>>> noisy. Is this normal specs?
>>>>
>>>> If it has semi break in mode then the relay can switch for start and finish
>>>> of two times. Very quaiet.
>>>>
>>>> Thanks all
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|