TenTec
[Top] [All Lists]

Re: [TenTec] rx 366

To: tentec@contesting.com
Subject: Re: [TenTec] rx 366
From: kc9cdt@aol.com
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 4 Jun 2012 17:16:45 -0400 (EDT)
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I was told that it is GC, but the original second RX was a little better in 
that mode..BUT the ham band function was like the Eagle (superb!).
73,
Lee



Lee Simmonds
Summit DCS LLC
 
260-799-4077 Office
260-403-6936 Cell



-----Original Message-----
From: Kim Elmore <cw_de_n5op@sbcglobal.net>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Sent: Mon, Jun 4, 2012 4:57 pm
Subject: Re: [TenTec] rx 366


I believe that John Henry has posted that the rx-366 DOES WORK as a gc rx. 
OWEVER, specifications apply ONLY to the Amateur bands.
73,
Kim N5OP

On Jun 4, 2012, at 15:38, John Molenda <cdistflatfoot@gmail.com> wrote:
> On 6/4/2012 3:38 PM, Carl Moreschi wrote:
> Yes, that is correct.  My N4PY Orion software has a setup to run the 366
> as VFO A for Panadpater use.
> 
> Carl Moreschi N4PY
> 121 Little Bell Dr.
> Hays, NC 28635
> www.n4py.com
> 
> On 6/4/2012 1:46 PM, John Molenda wrote:
>> On 6/4/2012 5:47 AM, Barry N1EU wrote:
>>> No on both counts.  I believe the 9Mhz out uses the existing "spare"
>>> connector and a pluggable jumper between RX366 and that connector.
>>> 
>>> 73,
>>> Barry N1EU
>>> 
>>> On Mon, Jun 4, 2012 at 1:44 AM, John Molenda<cdistflatfoot@gmail.com>    
rote:
>>>> Hello, I would like to know if the new Rx 366 board mod takes away
>>>> general coverage receive from the radio.  Does the radio need to be sent
>>>> back to TT for the 9 Megahertz out jack mod ?  thanks John Molenda
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>> OK so if we were to hook up to a pan adapter it would only be reading
>> what is on Rx 2or vfo 2  correct ?
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
 Thank you .  I am considering it I just do not want to give general 
 coverage.  John kb2huk
 _______________________________________________
 TenTec mailing list
 TenTec@contesting.com
 http://lists.contesting.com/mailman/listinfo/tentec
______________________________________________
enTec mailing list
enTec@contesting.com
ttp://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>