Good info Mike. Thanks. Nice to know the new formula is "current
technology" and can be used on most all substances without harm. I presume
the "5" in the designators is the 5% solution which is most adequate.
As stated earlier, my two bottles are 20+ years old and are the "100 proof"
formulations. I dilute with Freon TF for quick applications.
73
"old codger" Bob, K4TAX
----- Original Message -----
From: "Mike Hyder -N4NT-" <Mike_N4NT@charter.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Sunday, August 26, 2012 9:03 AM
Subject: [TenTec] Cramolin, etc.
Cramolin was manufactured by Caig Laboratories. Ten-Tec used two iterations,
the Red can was the contact cleaner and the Blue can was the
lubricant/preservative. They still make similar stuff.
Current Equivalents:
Old Red Can = DeoxIT® DN5 Spray
Old Blue Can = DeoxIT® SHIELD SN5 Spray
It is IMPORTANT to note that each formulation has the letter "N" in its part
number. That denotes the Non drip - Quick Dry Sprays which are SAFE ON
PLASTICS.
Here is a product info sheet: http://bit.ly/PfCV9u I suggest you avoid
their "Standard Sprays," which can attack plastics.
You can order from their store at http://store.caig.com/ but there is a $25
minimum. Other places sell it but one can of each will come to a bit over
$25 and used properly will last through the lifetime of your grandchildren.
Sorry to have posted information when it seems to really irritate some old
codgers on the reflector and I said I wouldn't.
73, Mike Hyder -N4NT-
----- Original Message -----
From: "wade staggs" <tvman1954@gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Sunday, August 26, 2012 00:25
Subject: Re: [TenTec] Omni VI plus Display
> *Hello Bob,*
> * Where do you purchase Cramolin these days? My supplier
> told me that the EPA had caused it to be pulled from the market because it
> contained 47% Trichlorotrifluroethane. I find that DeOxit works,but one
> formula in their line uses Naptha as the solvent. This is Not Good for
> some
> switches made of plastic. I clearly remember when TV sets changed from
> Real
> Tuners, with channel strips, to Rotary Encoder/Switches. That good old
> Tried and True tuner spray which had been used for decades, sure would
> mess
> an Encoder/Switch Up. To reword my question, can Cramolin still be
> purchased with a professional license?*
> * 73 to
> all Wade/KJ4WS*
>
> On Sat, Aug 25, 2012 at 10:30 PM, Bob McGraw - K4TAX
> <RMcGraw@blomand.net>wrote:
>
>> I agree with Jim. Having repaired several of the Omni VI series, the
>> areas
>> of concern are the connectors that are used between boards and with the
>> wiring harness terminations. Carefully unplug each, inspect around pins
>> with a bright light and magnification to assure no solder cracks exists.
>> Same for the IC's in sockets on the boards. I suggest a contact cleaner
>> such as Cramolin. But take caution in using any cleaner "least is best".
>> The put things back together and exercise each connector by then
>> unplugging
>> it again and re-inserting it. The wiping process cleans the pins, both
>> male
>> and female.
>>
>> You can check the data going to the LED displays all the way to the
>> segment
>> of the LED to see if there is a failure of the LED device or if a failure
>> exists elsewhere. I am not a proponent of changing parts to see if that
>> fixes a problem. I much prefer to spend the time to find the defective
>> part
>> and simply replace that part. The repair success rate is much higher
>> using
>> this method as opposed to putting in new parts and see what happens.
>> I've
>> found too many times that folks put in new, but defective parts, or make
>> solder errors which introduce added problems.
>>
>>
>> 73
>> Bob, K4TAX
>>
>>
>>
>> ----- Original Message -----
>> From: "Jim Goudie" <jagoudie@comcast.net>
>> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>> Sent: Saturday, August 25, 2012 10:07 PM
>> Subject: Re: [TenTec] Omni VI plus Display
>>
>>
>> > Paul,
>> >
>> > I have an Omni VI opt 3 that I purchased used. I have had multiple
>> > display problems. When I opened it up and checked out the display
>> > board,
>> > it was obvious that a previous owner had re-soldered things. I cured
>> some
>> > problems by fixing some bad solder joints. And there is a small flaky
>> > problem that I haven't found yet (though the rig is currently on the
>> > shelf).
>> >
>> > So, I'd suggest doing a good visual inspection of the board...
>> > re-solder
>> > carefully...
>> >
>> > A second possibility, maybe to try before the other... "exercise" the
>> > connectors on the wiring that goes to that board.
>> >
>> > 73 & good luck!
>> > Jim, AF3Z
>> >
>> >
>> > On Aug 25, 2012, at 7:32 PM, Paul A. Ramey wrote:
>> >
>> >> While using my radio today I lost all of the segments on the DSP1,
>> >> right
>> >> side digit. So now I get a read out that is 1 .225, 2 .225 instead of
>> >> 14.225 and 21.225. My computer programs shows the correct freq and I
>> >> am
>> >> TX/RX on correct freq. Have any of you had this happen? What was the
>> >> fix?
>> >> Any one have a parts radio that wants to sell a LED display board? I
>> >> am
>> >> also looking for the following keys that Ten Tec no longer stocks.
>> >> REV,
>> >> A=B and A/B
>> >>
>> >> Thanks for your help
>> >>
>> >> Paul, WG0G
>> >> _______________________________________________
>> >> TenTec mailing list
>> >> TenTec@contesting.com
>> >> http://lists.contesting.com/mailman/listinfo/tentec
>> >
>> > _______________________________________________
>> > TenTec mailing list
>> > TenTec@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/tentec
>> >
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|