TenTec
[Top] [All Lists]

Re: [TenTec] Using a Mac to install OMNI VII firmware

To: Clayton Brantley <clayton_n4ev@yahoo.com>, Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Using a Mac to install OMNI VII firmware
From: denton sprague <denton@oregontrail.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 10 May 2015 09:37:17 -0700
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Sad to say, but there is still very little ham software available for Macs.
For now the only apparent alternative is to keep a dedicated windoze pc 
available for ham software use.


On May 10, 2015, at 9:24 AM, Clayton Bra4P via TenTec <tentec@contesting.com> 
wrote:

> I thought the Mac wouldn't work. 
> 
> Clayton N4EV
> 
>      From: Mike Bryce <prosolar@sssnet.com>
> To: Clayton Brantley <clayton_n4ev@yahoo.com>; Discussion of Ten-Tec 
> Equipment <tentec@contesting.com> 
> Sent: Sunday, May 10, 2015 12:14 PM
> Subject: Re: [TenTec] Using a Mac to install OMNI VII firmware
> 
> Sorry to say, the mac’s won’t work. UNLESS you run “Parallels” a windows 
> emulator
> 
> Mike, WB8VGE
> SunLight Energy Systems
> The Heathkit Shop
> http://www.theheathkitshop.com/ <http://www.theheathkitshop.com/>
> J e e p
> o|||||||o 
> 
> A man with one clock knows what time it is. A man with two clocks is never 
> sure. 
> 
> 
> 
> 
> 
>> On May 10, 2015, at 11:39 AM, Clayton Brantley via TenTec 
>> <tentec@contesting.com> wrote:
>> 
>> You might check with the guys in Sevierville, but I don't think the updates 
>> will work with anythingBUT a Windows PC.  I use Linux as my main computer 
>> but I keep a PC around for what you aretaking about.
>> Clayton N4EV
>> 
>>       From: "Silevitch, Michael" <m.silevitch@neu.edu>
>> To: "TenTec@contesting.com" <TenTec@contesting.com> 
>> Sent: Sunday, May 10, 2015 8:14 AM
>> Subject: [TenTec] Using a Mac to install OMNI VII firmware
>> 
>> I have just purchased an OMNI VII and will be updating the firmware. I would 
>> prefer to use my Mac computer rather than a PC for this. I have a serial to 
>> USB adapter which should work to connect the OMNI to the Mac (or PC for that 
>> matter.) Any guidance would be appreciated. 
>> 
>> I may also want to operate the OMNI remotely using a Mac rather than a PC. 
>> Again any advice would be appreciated. 
>> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>