TenTec
[Top] [All Lists]

Re: [TenTec] Century 21 audio hum

To: Discussion of Ten-Tec Equipment <tentec@xxxxxxxxxxxxxx>
Subject: Re: [TenTec] Century 21 audio hum
From: Greg S via TenTec <tentec@xxxxxxxxxxxxxx>
Reply-to: Greg S <oldlongbeard@xxxxxxxxx>, Discussion of Ten-Tec Equipment <tentec@xxxxxxxxxxxxxx>
Date: Tue, 30 May 2017 22:27:15 +0000 (UTC)
List-post: <mailto:tentec@contesting.com>
I have used Sil-Glyde grease with great success. I can vouch for the fact that 
parts are not normally needed. But you will spend some time cleaning that old, 
dried farm implement lubricant they used ;-)
Greg, KC8HXO
--------------------------------------------
On Tue, 5/30/17, Howie WA3MCK <wa3mck@xxxxxxxxx> wrote:

 Subject: Re: [TenTec] Century 21 audio hum
 To: "Discussion of Ten-Tec Equipment" <tentec@xxxxxxxxxxxxxx>, "Josh Gibbs" 
<Gibbsjj@xxxxxxxxx>
 Date: Tuesday, May 30, 2017, 6:15 PM
 
 Tri-Flow? What is that Josh?
 I'm familiar with the flush/clean procedure. I
 have been told that 90W cup grease or bicycle
 chain lubricant is the way to
 go.
 What say you?
 
 On Tuesday, May 30, 2017, Josh Gibbs <gibbsjj@xxxxxxxxx>
 wrote:
 
 > Sounds like its
 time for a PTO clean and re-lube! I've been reading
 about
 > that procedure. Seems that
 usually the PTO parts are fine and you just need
 > to clean out the old grease and get some
 fresh grease in there. Some people
 > seem
 to recommend flushing out the old grease and then putting
 some
 > Tri-Flow in there. Would certainly
 be a lot less work!
 >
 > I hope Ten-Tec comes back to life and
 starts selling parts again!
 >
 > Thanks for checking that hum for me. Mine
 is definitely more than a slight
 >
 hum!
 >
 > -Josh
 >
 > On Tue, May 30, 2017
 at 2:54 PM, Howie WA3MCK <wa3mck@xxxxxxxxx
 > <javascript:;>> wrote:
 >
 > > Josh,
 > >
 > > Thank
 you
 > > for the info on the swamping
 resistor placement and installation.
 >
 >
 > > I have an analog C21. Bought
 it in the late 90's, had it on the air for a
 > > few years, sold it to Joe N2CX, he
 had it for 15 or 20 years, and I
 >
 bought
 > > it back s few years ago.
 > >
 > > It's
 beat up cosmetically but works fine. Replaced the finals not
 too
 > long
 > >
 ago... and now the PTO is starting to go - mechanically that
 is!
 > >
 > > Ok -
 just checked - yes, when I turn down the volume there is a
 slight
 > hum
 > >
 with my old 8 ohm mono headphones.
 >
 >
 > > I prefer to use the internal
 speaker which is fine for me and why I may
 > > have not noticed the low/level
 hum.
 > >
 > > By
 the way, I emailed TenTec several months ago concerning
 the
 > > availability of a PTO repair
 kit for the C21 analog xcvr. I received an
 > > answer a few weeks ago stating that
 they were in transition and to keep
 >
 an
 > > eye on their website. Nothing
 seen yet.
 > >
 >
 > Howie WA3MCK
 > >
 >
 _______________________________________________
 > TenTec mailing list
 >
 TenTec@xxxxxxxxxxxxxx
 <javascript:;>
 > http://lists.contesting.com/mailman/listinfo/tentec
 >
 _______________________________________________
 TenTec mailing list
 TenTec@xxxxxxxxxxxxxx
 http://lists.contesting.com/mailman/listinfo/tentec
 
_______________________________________________
TenTec mailing list
TenTec@xxxxxxxxxxxxxx
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>