Look at 2.2 SSB Operation AN (8). Page 14 in my manual.
Andy W3LI
________________________________
From: TenTec <tentec-bounces@contesting.com> on behalf of Gary F
<dukeshifi@comcast.net>
Sent: Wednesday, July 19, 2017 5:33 PM
To: w2iy@verizon.net; Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] notch filter for Eagle?
The Eagle does have a notch function. I don't recall how to activate it but it
is in the manual.
It's sort of useless, like all Ten Tec notch filters, since it is outside the
AGC loop, so, while it does not have the carrier, it also attenuated your
desired signal by about as much as it reduces the carrier.
The reduction to 20 watts in Tune is self-defense. Orion's do it too. This is
to prevent the presence of full 100 watts into a mismatch. It is good policy.
Orion's had an option in which you could press the Power button, I believe, to
get 100 watts in Tune after match had been reached.
Red arid green the A//B VFO, there really is no A or B VFO in the traditional
sense and Eagle only has one tuning knob. Therefore, the A/B indicator serves
no function in transceive operation. In split operation, that indicator should
flip when going fro RX to TX to tell you which displayed frequency is the TX
frequency.
Gary
Sent from my iPad
> On Jul 19, 2017, at 3:05 PM, Michael Tortorella <w2iy@verizon.net> wrote:
>
> Hi all, I am hearing an awful lot of steady carrier signals up here in the
> frozen north of Downeast Maine. Most are not very strong and they go away
> when I disconnect the antenna so they are external to the radio. Today I am
> chasing TR8CA on 20 CW, he is way down in the noise, and 100 Hz away from
> one of these carriers. Sure would be nice to have something like a notch
> filter to help in situations like these but I could not see anywhere in the
> manual or front panel where I could notch the offending carrier. Is there
> any list wisdom on this?
>
>
>
> On another note, I did contact service at TT last week with my question
> about power out in autotune; after only a few days delay I got an answer
> that the power out in autotune is 20 watts even though the power output
> shown on the display is 100. This seems not quite right from a human
> factors point of view, maybe there can be a firmware fix? Also, when
> exchanging VFOs, the A,B labels do not change even when the B vfo is in
> large type at the top of the display. I find this confusing. OK, I guess
> this turned into a longer letter about a couple of other things besides
> notch filtering, so please excuse my prolixity and thank for the BW. Any
> suggestions appreciated.
>
> Thanks and 73, Mike W2IY
>
>
>
> ---
> This email has been checked for viruses by AVG.
> http://www.avg.com
AVG 2017 | FREE Antivirus & TuneUp for PC, Mac, Android<http://www.avg.com/>
www.avg.com
Download FREE antivirus and malware protection. Tune up your PC, Mac and
Android devices for peak performance. Surf safely and privately, wherever you
are.
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
TenTec Info Page -
Contesting<http://lists.contesting.com/mailman/listinfo/tentec>
lists.contesting.com
Your email address: Your name (optional): You may enter a privacy password
below. This provides only mild security, but should prevent others from messing
...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
TenTec Info Page -
Contesting<http://lists.contesting.com/mailman/listinfo/tentec>
lists.contesting.com
Your email address: Your name (optional): You may enter a privacy password
below. This provides only mild security, but should prevent others from messing
...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|