TenTec
[Top] [All Lists]

Re: [TenTec] Audio improvements on Argonaut VI

To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Subject: Re: [TenTec] Audio improvements on Argonaut VI
From: <Rick@dj0ip.de>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Mon, 20 Aug 2018 20:05:36 +0200
List-post: <mailto:tentec@contesting.com>
I have only used the Argo 6 and Eagle on HF.
I can only hear the noise when turning the RF and AF all the way down.
While listening to signals, I don't hear it.

I do agree that Ten-Tec should not have sold the radio like that.
However I think it is misleading to portray this as a big problem.
After all, neither of the radios shipped with a transverter output.

Using these physically small radios for their original purpose, the problem,
though real, is of no consequence.

73,
Rick, DJ0IP
(Nr. Frankfurt, Germany)

-----Original Message-----
From: TenTec <tentec-bounces@contesting.com> On Behalf Of Paul Christensen
Sent: 20 August 2018 19:58
To: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
Subject: Re: [TenTec] Audio improvements on Argonaut VI

Rick,

It's more common and bothersome than you may think.  In fact, the OP raised
the issue, not me.  You will find reports of high residual audio levels
posted on eHam reviews.  Moreover, it's often audible when listening to
low-signal modes, especially on VHF/UHF when using transverters.

Paul, W9AC

-----Original Message-----
From: TenTec <tentec-bounces@contesting.com> On Behalf Of Rick@dj0ip.de
Sent: Monday, August 20, 2018 1:33 PM
To: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
Subject: Re: [TenTec] Audio improvements on Argonaut VI

Paul,

Technically you are correct, but practically it is of no consequence.

This noise is inaudible when you use the radios to listen to signals.
You notice it only when you turn the audio way down to the point that you
hardly hear anything anymore.

Under normal use, it is of no consequence.

73,
Rick, DJ0IP
(Nr. Frankfurt, Germany)

-----Original Message-----
From: TenTec <tentec-bounces@contesting.com> On Behalf Of Paul Christensen
Sent: 20 August 2018 19:21
To: 'Discussion of Ten-Tec Equipment' <tentec@contesting.com>
Subject: Re: [TenTec] Audio improvements on Argonaut VI

>"Have you heard, observed or measured the artifacts of this receiver?    If
not, you have no clue as to the minuscule magnitude of the issue."

Thanks Bob, but I think I have a clue.  People who actually know me (and my
background) also think I have a clue.  I regularly use high-end audio test
equipment in my noise, level, and distortion measurements.  Audio test
equipment includes a Tektronix AA-501A analyzer with an ultra-low-distortion
SG-505 module.  The Tek equipment is visible on the operating desk as shown
on my QRZ.com page.  I also use SpectraPlus software with a pro-grade sound
card.

I stand by my prior comments.

Paul, W9AC  

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>