Hi MartinHow are you keeping there in HS land, long time since I have seen you
here in P/Boro'.Now the Argosy:TX works but power level drops off after a few
seconds, I took the filter out, nothing, got to either bridge it out like you
say or does the filter switch on the front do the same job?.Will be playing
with it later as I have some urgent maint' on my bungalow to do this
morning.Feel free to chip in with any pearls of wisdom that you can think of,
all appreciated mate. I have been relying on Steve, he is a fountain of
knowledge on the TT brand.regards73Snowy
On Saturday, 1 September 2018, 6:17, Martin Sole <hs0zed@gmail.com> wrote:
Just adding to my points below. Is the transmitter working okay? If not
maybe try bridging the crystal filter?
Martin, HS0ZED
On 01/09/2018 12:14, Martin Sole wrote:
> Hi Snowy,
>
> Whenever I've had similar problems, and it does happen time to time
> here though different rigs, never seen an Argosy, it's often a result
> of a nearby surge event, lightning strike. Look at T1 and T6 to see if
> they are particularly fine wire. In all the cases I've seen similar
> deafness it has been either switching diodes that are open circuit or
> a fine wire transformer with an open circuit winding. Even with the
> sig gen as far back as C11/D4 I would think -80 to -90 should produce
> a fair signal.
>
> Martin, HS0ZED
>
>
> On 01/09/2018 01:41, ROLAND HOWELL via TenTec wrote:
>> Hi SteveOk injected signal into con 32, no difference to sensitivityAs for
>> why r25 burnt out I can't answer that but it was definitely cooked.I have
>> spoken to the ex owner of the radio and he states that he was using it thru'
>> a tuner when it went wrong and he smelled smoke, the burnt components!That
>> was why I changed the sensing diodes in case they had been damaged.Snowy
>> G0HZE
>>
>> On Friday, 31 August 2018, 18:55, Steve Hunt<steve@karinya.net> wrote:
>>
>>
>> How sensitive is it if you inject a signal directly after the BPF at
>> connector 32 on the RF mixer board? That would eliminate a lot of the
>> front-end diode switching.
>>
>> PS - not sure why R25would burn out - it doesn't carry any DC current
>> according to the schematic.
>>
>> Steve G3TXQ
>>
>> On 31/08/2018 17:20, ROLAND HOWELL via TenTec wrote:
>>> Hi SteveThanks for replying my shout for guidance on the ARGOSY 2 525d
>>> problem that I have.Yes it is the same on all bands.Now on removing the top
>>> cover to look at the innards I saw on the mixer board I had 3 x burnt
>>> components 2 x 8.2ohm and 1 x 150ohm resistors ( R,s 24-26),these changed
>>> as well as the associated small 'C,s, again no difference ,I have followed
>>> the path back from the 'S' meter and replaced Q2 and Q11 on the if/audio
>>> board, no difference.Went back to the low pass filter ( the odd numbered
>>> one 91696 not what is in the manual) and changed the BAT41 diodes in the
>>> sensing circuit, you guessed it, no difference.HELP hi hiI have noticed
>>> that it seems to be off frequency, I inject a signal of 7.050mHz but seem
>>> to get a better tone at 7.045mHz and a small bit of life in the 'S' meter
>>> but it still requires a massive input signal in to show any life, the TX
>>> indication is spot on.Regards73Snowy
>>>
>>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|