Either add large galvanized washers on the low side to compensate for
the difference or put some nuts on the bottom of the plate bolts and
make an upward adjustment as needed.
Herb Schoenbohm, KV4FZ
On 12/11/2015 11:42 PM, Douglas Ruz (CO8DM) wrote:
Boxbe <https://www.boxbe.com/overview> This message is eligible for
Automatic Cleanup! (co8dm@frcuba.co.cu) Add cleanup rule
<https://www.boxbe.com/popup?url=https%3A%2F%2Fwww.boxbe.com%2Fcleanup%3Ftoken%3DAO1endMB4BGojkncw4tCjRcsIft8fvXGj1hxkDNRGxIiQT6SLSsFa3Jt6gz9LHV5xu2Rnw7Xpf7T1e%252BhgNQDRNmtX6%252BLwHQqW6NcpgoTxdlhSBxphSyPh%252FHOaI7Uh%252FrfsZzKPbEfqvI%253D%26key%3DQ7ts5buEDqBDM1tNb9O4fPb9HflHfdJ%252FTCGt%252BbVHYHY%253D&tc_serial=23620245590&tc_rand=1824117425&utm_source=stf&utm_medium=email&utm_campaign=ANNO_CLEANUP_ADD&utm_content=001>
| More info
<http://blog.boxbe.com/general/boxbe-automatic-cleanup?tc_serial=23620245590&tc_rand=1824117425&utm_source=stf&utm_medium=email&utm_campaign=ANNO_CLEANUP_ADD&utm_content=001>
Thanks Ron,
Interesting idea using a solid hard wood shim a little larger than the
base.
Bolts diameters are 3/8".
Bolts length are 2 1/2".
are not ok 4 bolts with that dimension to fix a base to the roof for 3
tower sections like Rohn 25G ?
73....Douglas, CO8DM
"No creo que haya alguna emoción más intensa para un inventor que ver
alguna de sus creaciones funcionando. Esa emoción hace que uno se
olvide de comer, de dormir, de todo." - Nikola Tesla
----- Original Message ----- From: "Ron W8RJL" <youngron@verizon.net>
To: "Douglas Ruz (CO8DM)" <co8dm@frcuba.co.cu>
Sent: Friday, December 11, 2015 10:22 PM
Subject: Re: [TowerTalk] how to install the tower base over a sloping
roof???
Doug,
See attachment. You can make a solid hard wood shim a little larger
than
the base. You would need longer bolts. 3/8" does not sound very big.
Use as
large as practical.
Good luck with your project.
Ron W8RJL
----- Original Message ----- From: "Douglas Ruz (CO8DM)"
<co8dm@frcuba.co.cu>
To: <towertalk@contesting.com>
Sent: Friday, December 11, 2015 8:00 PM
Subject: [TowerTalk] how to install the tower base over a sloping
roof???
Hi,
I would like install an small tower over the concrete roof, only 3
sections, 10 ft each. 2 set of guy wires (3 + 3).
I install the 3 anchor points but when i try intall the tower base i
found
the roof is not 100 % flat. It is an sloping or pitching roof...it
is very
soft...about 5, 7 or 10 degrees. i am planning bolt the base to the
roof
but not crossing the roof...i will bolt the base in 4 points with
3/8 inch
bolts and will drill about 2 1/2 inch inside the roof.
How can i correct the sloping to put the base 100% flat (level) ???
Thanks,
73....Douglas, CO8DM
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|