WriteLog
[Top] [All Lists]

[WriteLog] UserPort

To: <writelog@contesting.com>
Subject: [WriteLog] UserPort
From: va3mw@portcredit.net (VA3MW - Port Credit)
Date: Fri May 2 21:29:13 2003
Bob

This is what my INI file looks like.  I spent 2 full days debugging this.  I
use USERPORT as well.

I also added the line CW_ON_PIN1=1 to get rid of chopping sending.

Mike

[Ports]
COM1:=9600,n,8,1
COM2:=9600,n,8,1
COM3:=9600,n,8,1
COM4:=9600,n,8,1,p
dvktype=2
dvkport=0
cwtype=2
cwport=6
dvkstoploop=1
dvkechomic=1
Comm3Used=USED,POLL,34
Comm3RigManager={D0DE9422-0517-11D4-9D1B-00105AA43DDF}
Comm3Baud=19200
Comm3XmitControl=ALWAYS
CWPTTCONTROL=1
CWPTTDELAY=0
CW_ON_PIN1=1


----- Original Message -----
From: "Bob Lafont" <bob@wa2mno.ampr.org>
To: "Writelog" <writelog@contesting.com>
Sent: Friday, May 02, 2003 8:12 PM
Subject: RE: [WriteLog] UserPort


> Actually, this is a re-installation of WL so the writelog.ini file is
> bare-bones. No other LPT config statements exist in the config.
>
> Also, Device Manager shows LPT1 as 0x0378-0x037F and 0x0778-0x077B.
> 0x0378-0x037F is what is configured in UserPort. I also tried
0x0778-0x077B
> but that could not be accepted.
>
> LPT2 still shows as the active LPT port in WL.
>
> Do people have this kind of difficulty with Direct-IO ?
>
> Bob
>
> -----Original Message-----
> From: VA3MW [mailto:va3mw@rogers.com]
> Sent: Friday, May 02, 2003 5:07 PM
> To: Bob Lafont; Writelog
> Subject: Re: [WriteLog] UserPort
>
>
> Try deleting all the LPT entries in writelog.ini.
>
> That was the only way I got it to work.
>
> Mike
> ----- Original Message -----
> From: "Bob Lafont" <bob@wa2mno.ampr.org>
> To: "Writelog" <writelog@contesting.com>
> Sent: Friday, May 02, 2003 1:01 AM
> Subject: [WriteLog] UserPort
>
>
> > I am running XP and cannot get UserPort to work properly. Following the
> > instructions provided by UserPort I added LPT1 with 0x378-0x37B. After
> > selecting Update, Start and Exit and starting WriteLog I find that LPT2
is
> > selectable in the setup screen, not LPT1. When I select both CW and DVK
> > using LPT2 the sound card generates audio just fine but when switching
to
> CW
> > I cannot get it to generate at CW at all.
> >
> > Any ideas on what my problme might be?
> >
> > Bob /wa2mno
> >
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/writelog
> >
>
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
>
>


<Prev in Thread] Current Thread [Next in Thread>