Thank you to all who replied back to me on this issue.
I have been able to get LPT1 to show up in WL config screen but still no CW
keying.
As a comparison, N1MM worked properly using DLPORTIO. DLPORTIO is freeware.
I believe the problem with UserPort is that it is not properly controlling
the DX Doubler SO2R box I am using. In order for my DXD box to work with
N1MM/DLPORTIO I need to switch the DXD box to auto on the xmit side. When
using WL with UserPort and throwing the DXD xmit switch to auto causes the
radio to key up constantly but never any CW keying.
I suppose it would be too difficult to make WL work with DLPORTIO or would
it? Of course, that would probably mean anyone who paid for DirectIO would
no longer be able to use it any longer.
Is anyone using UserPort with a DXD SO2R box ?
Thanks!
73 - Bob
-----Original Message-----
From: writelog-bounces@contesting.com
[mailto:writelog-bounces@contesting.com]On Behalf Of VA3MW - Port Credit
Sent: Friday, May 02, 2003 8:29 PM
To: Bob Lafont; Writelog
Subject: Re: [WriteLog] UserPort
Bob
This is what my INI file looks like. I spent 2 full days debugging this. I
use USERPORT as well.
I also added the line CW_ON_PIN1=1 to get rid of chopping sending.
Mike
[Ports]
COM1:=9600,n,8,1
COM2:=9600,n,8,1
COM3:=9600,n,8,1
COM4:=9600,n,8,1,p
dvktype=2
dvkport=0
cwtype=2
cwport=6
dvkstoploop=1
dvkechomic=1
Comm3Used=USED,POLL,34
Comm3RigManager={D0DE9422-0517-11D4-9D1B-00105AA43DDF}
Comm3Baud=19200
Comm3XmitControl=ALWAYS
CWPTTCONTROL=1
CWPTTDELAY=0
CW_ON_PIN1=1
----- Original Message -----
From: "Bob Lafont" <bob@wa2mno.ampr.org>
To: "Writelog" <writelog@contesting.com>
Sent: Friday, May 02, 2003 8:12 PM
Subject: RE: [WriteLog] UserPort
> Actually, this is a re-installation of WL so the writelog.ini file is
> bare-bones. No other LPT config statements exist in the config.
>
> Also, Device Manager shows LPT1 as 0x0378-0x037F and 0x0778-0x077B.
> 0x0378-0x037F is what is configured in UserPort. I also tried
0x0778-0x077B
> but that could not be accepted.
>
> LPT2 still shows as the active LPT port in WL.
>
> Do people have this kind of difficulty with Direct-IO ?
>
> Bob
>
> -----Original Message-----
> From: VA3MW [mailto:va3mw@rogers.com]
> Sent: Friday, May 02, 2003 5:07 PM
> To: Bob Lafont; Writelog
> Subject: Re: [WriteLog] UserPort
>
>
> Try deleting all the LPT entries in writelog.ini.
>
> That was the only way I got it to work.
>
> Mike
> ----- Original Message -----
> From: "Bob Lafont" <bob@wa2mno.ampr.org>
> To: "Writelog" <writelog@contesting.com>
> Sent: Friday, May 02, 2003 1:01 AM
> Subject: [WriteLog] UserPort
>
>
> > I am running XP and cannot get UserPort to work properly. Following the
> > instructions provided by UserPort I added LPT1 with 0x378-0x37B. After
> > selecting Update, Start and Exit and starting WriteLog I find that LPT2
is
> > selectable in the setup screen, not LPT1. When I select both CW and DVK
> > using LPT2 the sound card generates audio just fine but when switching
to
> CW
> > I cannot get it to generate at CW at all.
> >
> > Any ideas on what my problme might be?
> >
> > Bob /wa2mno
> >
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/writelog
> >
>
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
>
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
|