Steve,
I took it that you got to 10.57H via an "upgrade" rather than a "full"
install. Soooo, I crossed my fingers and upgraded my 10.57H FULL install
to10.58E using the wl1058emsiupg.zip file as instructed by Ron. Viola,
works like a champ! No problems at all. I run WinME so I did upgrade my
Windows installer program per Ron's missive of a couple of weeks ago in
order to get the 10.57H FULL install to load properly.
Gary AL9A
----- Original Message -----
From: "Steve AI9T" <steve@ai9t.com>
To: "Gary Senesac AL9A" <al9a@pobox.mtaonline.net>; "'WriteLog Reflector'"
<writelog@contesting.com>
Sent: February 22, 2006 3:18 AM
Subject: Re: [WriteLog] Ver-10.58E now ready to download...
> Gary
>
> 10.57H was the last update I had installed around 1-14-2006. At least
> that is the date on the folder I created for the update files.
>
> --
> 73
>
> Steve AI9T
>
> http://www.ai9t.com
>
> QSL via LOTW and EQsL
>
>
>
>
>
> Gary Senesac AL9A wrote:
>
> >Steve,
> >How did you get to 10.7H? Was it an incremental upgrade from 10.56 or
> >earlier, or was your 10.57H a FULL install. Ron's announcement message
> >indicates that the wl1058emsiupg.zip file is for use only if you got to
> >10.57H via a FULL install. I just did an uneventful FULL install of
10.57H
> >last night and downloaded wl1058emsiupg.zip this afternoon. After seeing
> >your problems I'm holding off on the upgrade pending further
clarification.
> >It appears to me the wl1058eupg.zip is for WL versions that had the last
> >FULL install at 10.56 or earlier, thus my question about the upgrade path
> >that got you to 10.57H.
> >Gary AL9A
> >
> >----- Original Message -----
> >From: "Steve AI9T" <steve@ai9t.com>
> >To: "Steve AI9T" <steve@ai9t.com>
> >Cc: "Ron Stailey" <k5dj@austin.rr.com>; "'WriteLog Reflector'"
> ><writelog@contesting.com>
> >Sent: February 21, 2006 6:15 PM
> >Subject: Re: [WriteLog] Ver-10.58E now ready to download...
> >
> >
> >
> >
> >>All
> >>
> >>I finally got everything working again and upgraded. After doing another
> >>system restore and restoring the contents of the WL program folder. I
> >>was able to complete the upgrade from 10.57H to 10.58E with the
> >>wl1058eupg.zip file, not the (wl1058emsiupg.zip)
> >>
> >>Be careful which file you choose
> >>
> >>--
> >>73
> >>
> >>Steve AI9T
> >>
> >>http://www.ai9t.com
> >>
> >>QSL via LOTW and EQsL
> >>
> >>.
> >>
> >>Steve AI9T wrote:
> >>
> >>
> >>
> >>>Hello
> >>>
> >>>After doing a system restore, I unziped the contents of the
> >>>wl1058eupg.zip to another folder "as I always do" and then ran setup.
> >>>Program appeared to upgrade OK and the WL splash screen said 10.58E
when
> >>>starting. However, when I click on a recently used log I get an error
> >>>"Can't open DXCC data base file DXCCWAE.DAT" then log opens. If I enter
> >>>a call I get no country information.
> >>>
> >>>Running XP SP2 all updates.
> >>>
> >>>
> >>>
> >>>
> >>>
> >>_______________________________________________
> >>WriteLog mailing list
> >>WriteLog@contesting.com
> >>http://lists.contesting.com/mailman/listinfo/writelog
> >>WriteLog on the web: http://www.writelog.com/
> >>
> >>
> >>
> >
> >
> >
> >
>
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|