Same as me, homebrew transistor interface on com7. Also works with other
programs.
Thanks,
Gordon - N1MGO
On 5/2/2021 12:54 PM, Don Hill AA5AU wrote:
Forgot to mention, using v12.59F with homebrew transistor interface on COM1.
Works OK with other programs.
Don AA5AU
-----Original Message-----
From: WriteLog [mailto:writelog-bounces@contesting.com] On Behalf Of Don
Hill AA5AU
Sent: Sunday, May 2, 2021 11:52 AM
To: 'Gordon LaPoint'; 'Ed W0YK'; 'WriteLog'
Subject: Re: [WriteLog] CW Problems.
I have the same issue. When set to PC generates CW and my normal COM port
for CW, PTT keys all the time. No way to turn it off that I can find other
than to select an unused COM port.
Don AA5AU
-----Original Message-----
From: WriteLog [mailto:writelog-bounces@contesting.com] On Behalf Of Gordon
LaPoint
Sent: Sunday, May 2, 2021 9:58 AM
To: Ed W0YK; WriteLog
Subject: Re: [WriteLog] CW Problems.
Ed,
Sorry, PTT keys and stays keyed (I have an LED on my home brew
RS232 interface for CW/PTT/FSk, and the Radio is in TX, no CW sent
unless I hit an F key, then it sends, but stays in TX)
CW Generation is "PC generates".
This hardware combination does work with N1MM and DXLabs for proper CW,
with OR without PTT being used. I normally run QSK so no PTT is
normally used, but did test with the other software to insure my
hardware is good. I use the same RS-232 interface for RTTY with TXD for
FSK and RTS for PTT. I de-select the port in rttyrite when doing CW to
prevent conflicts.
Thanks,
Gordon - N1MGO
On 5/2/2021 10:30 AM, Ed W0YK wrote:
Hi, Gordon.
What does "keys and stays keyed" mean? PTT or CW keying? Which CW
generation method is selected in WL?
73,
Ed W0YK
-------- Original message --------
From: Gordon LaPoint <gordon.lapoint@gmail.com>
Date: 5/2/21 06:48 (GMT-08:00)
To: WriteLog <writelog@contesting.com>
Subject: [WriteLog] CW Problems.
Hi,
I'm setup for the NEQP, SSB works fine. when I switch to CW the
radio keys and stays keyed, can not find what I have setup wrong.
Radio - Kenwood TS590sg Ports set to COM18 115200 - works fine,
tracks radio frequency/mode
CW - COM 7 DTR= CW RTS= PTT
CW Options:
PTT Control (CW Mode ONLY) None (QSK) selected (tried "as specified
in Ports", no difference)
PTT to CW delay 0
PC generates sends CW space on startup - Checked (also tried unchecked
- no difference.
What else should I check?
This used to work, so don't know what changed except upgraded to 12.59F
, so downgraded to 12.56c, no change.
The same hardware setup works with N1MM and DX Labs, so I know the
hardware is good!!!!
Thanks,
Gordon - N1MGO
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|