Towertalk
[Top] [All Lists]

Re: [TowerTalk] N connector, Re: UHF (PL259) soldered center

To: Jim Thomson <jim.thom@telus.net>
Subject: Re: [TowerTalk] N connector, Re: UHF (PL259) soldered center
From: Michael Clarson <wv2zow@gmail.com>
Date: Tue, 26 Jun 2018 10:31:02 -0400
List-post: <mailto:towertalk@contesting.com>
Jim: The wireless industry is starting to use another connector -- the
4.3/10 DIN. Much more robust than the Type N, but unlike the 7/16 DIN, it
is sized for greater connector density for feed-lines typically used by
hams. Great. Now I have to get even more interseries adapters! --Mike,
WV2ZOW

https://www.amphenolrf.com/connectors/4-3-10.html

On Tue, Jun 26, 2018 at 10:18 AM Jim Thomson <jim.thom@telus.net> wrote:

> Date: Mon, 25 Jun 2018 22:35:21 -0700
> From: Avery Davis <wb4rtp@mindspring.com>
> To: "Charlie@thegallos.com" <charlie@thegallos.com>
> Cc: towertalk@contesting.com
> Subject: [TowerTalk] N connector, Re:  UHF (PL259) soldered center
> with braid crimp or, crimp-crimp, supply?
>
> <Charlie,
> <Would you please share a link to a source that discusses the limits of N
> <connectors?? Everything I have seen so far suggests they have as good or
> <better power handling at low frequencies than the PL-259, and are much
> <better at UHF as they are constant impedance (lower loss, higher power,
> <lower SWR).? For example, Amphenol rates their SO-239 at 500 V, while
> <their Type N is rated at 1500 Volts.? That sounds like better power
> <handling, to me.? The current rating wasn't listed, but I would think
> <that they would be about the same as the wire gauge in the coax cable
> <center conductor, since both connectors have center contact outer
> <diameter about the same as RG-8 or RG-213 coax, especially if skin-depth
> <effects are taken into account.?
> <I would appreciate a link to a better source of information on this.
> <73,
> <Avery, WB4RTP
>
> ##  Forget what amphenol  states.  A  teflon PL-259  will hi pot test a
> heck of a lot higher
> than a  Type N.   Type N uses a puny center pin, identical to a BNC. The
> center pin
> on any PL-259 is huge by comparison.  There is no RF on the center pin any
> way. The
> RF travels down the outside of the mating female of the   SO-239.   You
> can stuff  10+ kw
> through a  quality  teflon silver, correctly installed   PL-259 +  SO-239
> pair.   Avoid high swr, which can
> easily be fixed, right at the feed point.   10 kw = 707 volts RMS... =
> 1000 volts peak.   10 kw =  14 A RMS.
> 5kw =  10A  RMS  and  500 Vrms.... =  707 Volts peak..which is dick.   You
> wont blow anything up  with 1.5 kw.
>
> ##     The next step above the silver teflon  PL-259 and  SO-239 setup is
> the teflon silver 7-16 DIN connector.
> The 7-16 is the real deal.  Nobody uses  Type N anymore, the telcos all
> dumped the type N  years ago..and swapped
> to 7-16 din.   What really looks silly is  huge heliax,  like .875 and
> bigger variety... with a type N connector installed,
> complete with the puny BNC sized center pin.
>
> Jim   VE7RF
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>