TenTec
[Top] [All Lists]

Re: [TenTec] RASCAL interface and the Orion 565

To: "Rick W" <ve7tk@yahoo.ca>, "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] RASCAL interface and the Orion 565
From: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 16 Oct 2012 23:24:13 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
The Tentec supplied dongle has 4 cables/connectors.

They are:
Line Audio In = white - to pin 1 from computer sound card
Line Audio Out = yellow - to pin 4 to computer sound card
PTT = black to pin 3 - either a foot switch of manual switch. Can be controlled from the RS-232 connector on the computer.
FSK = FSK to pin 2 - must toggle from high to low for mark / space

For true FSK {and not AFSK} a proper interface will be required to toggle pin 2 from high to low for proper mark-space operation. The radio should be in FSK mode. To activate PTT take pin 3 to ground.

The easiest way, use the Tentec 712 USB soundcard interface and the computer software of your choice. No fuss, no mess, no external box to adjust. The computer software handles all the levels and switching. Only have to select AUX for the TX audio source.

73
Bob, K4TAX


----- Original Message ----- From: "Rick W" <ve7tk@yahoo.ca>
To: "Ten-Tec Reflector" <tentec@contesting.com>
Sent: Tuesday, October 16, 2012 10:57 PM
Subject: Re: [TenTec] RASCAL interface and the Orion 565


Jack is correct the Orion AUX jack has output that can be used for AFSK . FSK on the other hand is more of an issue. If your friend is using the Ten-Tec AUX cable for FSK I'm afraid he's out of luck. That cable does not bring out the FSK output. He'll have to build up a new cable or perhaps purchase one from a 3rd party.

I'm using a US-Interface Navigator and it keys the rig with the PTT on pin 3 and sends FSK on Pin 7 of the AUX jack. It has it's own DIN connector and privides access to all pins on the Orion's AUX jack.

Also, if your friend has an "early" 565 he may need to add a 10k pull up resistor between pin 7 of the AUX connector and pin 8 of the REMOTE jack.

http://www.ad4c.us/Tentec%20HF%20manuals_/Orion%20II/02Orion%2520FSK.pdf


73,
Rick
VE7TK


Website:  http://www.ve7tk.com

To:Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject:Re: [TenTec] RASCAL interface and the Orion 565
From:"k0bx@arrl.net" <k0bx@arrl.net>
Reply-to:Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date:Tue, 16 Oct 2012 17:35:17 -0700 (PDT)
List-post:<tentec@contesting.com">mailto:tentec@contesting.com>
That is very good Jack, the problem is that I am not the owner of the Orion but
my friend W0TT is.  I am trying to get him on RTTY.
Maybe you could send me a note off line on what cables you are talking about?
We do want to be able to use FSK and NOT AFSK.  And do CW without changing
cables. Joe K0BX Stop the insanity!
Please do not add me to any distribution lists (Joke, Stories or Junk) without
my permission. ________________________________
From: jack <jfriend31@comcast.net>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Sent: Wed, October 17, 2012 12:31:38 AM
Subject: Re: [TenTec] RASCAL interface and the Orion 565 One does not need a Rascal for RTTY with the Orion. one can use the cables that came with Orion for RTTY direct to the computer. I have done exactly that for all the years I have had my Orions 565, mostly CW but MixW3 will do all modes
just about with the above cable connections to computer.
jack
ak7o
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec


_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>