TenTec
[Top] [All Lists]

Re: [TenTec] Reasons to buy an OM7 instead of an Eagle

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Reasons to buy an OM7 instead of an Eagle
From: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Thu, 10 Jul 2014 07:20:33 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Rick et al;

Your comments are very appropriate. Yes, merge my comments and observations with yours.

Last evening with the two radios sitting in front of me, I quickly created the list. There is a lot more that could have been added. From my take, numbers are numbers, and the real proof of the pie is actual on the air usage in a given location and specific circumstances. In many cases today one will actually need two or more radios on the desk to make a real and valid evaluation. To this end, the Tentec 30 day trial period does exactly this and this is something no other company provides.

Rob has done an outstanding job of measuring and presenting results of many receiver brands and models. He is to be highly commended for his excellent work. I do caution, those looking to his Receiver Test Data, should understand exactly what is being presented. Just because the particular brand and model is at the top of the list or any ranking for that matter, does not make it "the best" or better than another one on the list. I have downloaded the list to EXCEL and thus I can sort on any parameter. When this is done one will find other brands and models appear at the top of the list. I find there is no receiver on the list that consistently appears at or near the top with any relevance of sort routine.

There are other factors which I view that make for a "good receiver". I personally place a lot of weight on receive audio quality. To that I do include the internal speaker, what ever it may be. One point I will not accept is poor audio quality for it makes not only inferior sound but for extended listening it is very fatiguing. To support this point, I recently loaned my Eagle to a close friend. While it was on his desk, his wife commented; "that little radio sounds much better than the ones you have". He has other brands and models, some much more expensive than the Eagle, pre or post sale promotion prices. From my take, the best receiver performance but with poor or inadequate audio is a lousy receiver. Thus I say what good is all the advanced electronics ahead of the audio chain? In speaking of "chain" ---- the strength of a chain is defined by its weakest link. A poor audio system makes for a poor receiver.

Tentec has always been known for good quality audio both on TX and RX. With this and other good quality attributes, their on air performance usually is equal to or is better than most other brands or models.

Clearly the difference between the Omni VII and the Eagle are quite notable. I find it necessary to use slightly different operating techniques with the two radios in order to attain optimum results with each one. Thus I've always said, don't operate a Tentec radio like others one may have or use. They are distinctly unique and different.

***************
As to the background pertaining to the current sales promotion, I can speculate on this just like many others have done. One point I've not seen advanced in these discussions is one I've not expressed but will do so.

Perhaps with the age of the Omni VII and the Eagle and the technology in the Argonaut VI, like most companies, Tentec has realized and amortized their R & D costs for these products. Once R & D is amortized, those costs are usually no longer included in the cost of the manufactured product. Therefore the costs have gone down and the new reduced cost basis can be then factored to retail price. It is this new price that is not being used to sell the products.

As a case and point, about 5 years ago we purchased a 42" Sony HD LED TV for about $2200. Last year a lightning strike destroyed that TV. It was replaced with a 48" Sony HD LED TV for about $899.

****************


73
Bob, K4TAX




----- Original Message ----- From: "Rick - DJ0IP / NJ0IP" <Rick@DJ0IP.de>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Thursday, July 10, 2014 2:29 AM
Subject: Re: [TenTec] Reasons to buy an OM7 instead of an Eagle


Bob,

That was good stuff.
If I find the time, I will try to merge both our lists into one.
I just now noticed, the OM7 announced in 2004, not 2007, so it has been 10
years since I have used or even seen an OM7.

I would like to say a few words about receiver performance now, showing ON
THE AIR TESTS made on the OM7.

Rob Sherwood's list shows measured lab numbers and Rob shares with us his
opinion of what is required by most people in order to have a good enough
receiver.  What few people have picked up on is that he has raised the
numbers by 5%. He is now saying 75dB BDR3 for SSB and 85dB for CW. This is
slightly higher than what the OM7 can achieve (on CW) but lower than the
Eagle.

NEVER-THE-LESS, those are just numbers, meaningless to most of us hams.
So what real world difference does it make?

Perhaps I am the only person who ever tested and 'documented' this in a real
world environment that showed a distinct difference.  In reality, 99.9% of
us will never have that environment AND that specific environment can no
longer be reproduced.
However, I do want to point out that at that time, there was indeed a very
distinct advantage in favor of the radio with the highest BDR3.

In 2004, a couple of weeks before the OMNI VII announced, I conducted a
transceiver test (I think I called it "intermod shootout") at one of our
contest sites.  The test was conducted on 40m on a Friday evening, but no
big contest was running.  However this was BEFORE the shortwave broadcast
stations had moved outside of the ham band, so the total amount of voltage
hitting a receiver's front end (here in Europe) was tremendous! Tremendous
because I was using a 3 element 40m Yagi at 105 ft. height.  This
environment can never be repeated because the broadcast stations are gone
now.

In addition, rotating the beam made a big difference in the amount of
intermodulation generated by the receivers and the direction
North/North-East was the worst.  I left the beam in that direction, then
compared several transceivers.
At that time, the "Meister" was the Orion (1).  There was no Eagle or O2
yet.

The (sometimes significant) difference between all 7 transceivers tested was
recorded in a video (for each radio) showing the S-Meter and recording the
accompanying sound.  You can see and hear the difference in these videos.
These results have been posted on the Bavarian Contest Club web site for
more than 10 years now.

Lots of people speculate about all kinds of things including receiver
performance and Ten-Tec going out of business.
I haven't figured out a way to benchmark TT going out of business, but I do
know how to test receivers in a real world environment, and when I test
stuff, I post it to the Internet for everyone to see and hear.

In today's environment, the only way to approximate this type of challenging
band condx is to operate in the middle of a very BIG contest, such as CQWW
DX contest, especially in CW!  AND, as I stated earlier, when operating,
don't skip over the messy pile-ups, jump in and work the station on that
frequency.  THAT'S WHERE THE DIFFERENCE IS!

I've posted this link several times before but I'll post it again.
Here's the LINK:
http://www.bavarian-contest-club.de/reviews/Transceiver-intermod-shootout-on
-40M-in-europe-;art32,565
Look under "RESULTS" to find clickable links to the video files.

(NOTE: most likely the link will be broken by the reflector. Copy it -both
lines of it, together- and paste it into your browser).

Two comments:  first, I am indeed the world's worst photographer, which is
evident from these videos, but the message does come through.  Second, in
the excitement, I sometimes unknowingly switched to speaking German instead of English. That's because the station owner who is German was testing with
me and he was commenting to me in German, causing my brain to switch from
7-bit to 8-bit ASCII.  I guess there was a sticky bit! (hi)

THE BOTTOM LINE:
Receiver performance is a highly misunderstood subject, partly because we
each have our own definition of what our needs are.  It is impossible to
make a list ranking true receiver performance and reflect the true
performance of each radio. Rob is the first person to tell us that in all of
his presentations.  He tells us of the many other important things, first
and foremost, "you have to enjoy using the radio".  THIS IS MORE IMPORTANT
THAN ANY LIST, and the only person on the planet that can determine that is
YOU.

Rob's list shows the radios ranked by BDR3, nothing more.
It may be used as one of many selection criterion but it certainly is not
the most decisive one.

The biggest difference between the Eagle and the OM7 is in the ergonomics of
the radios.
How you use them and navigate the menus is VERY different.
Many people will not like the Eagle.  I love it.
Some may not like the OM7 because it doesn't have separate AF/RF gain
controls and because it's Panadaptor is not very good. Other than that, my
guess is that most people will be more comfortable operating to OM7.

But if you are a serious contester, take the Eagle (unless you absolutely
need OmniRig support).

73 - Rick, DJ0IP
(Nr. Frankfurt am Main)


-----Original Message-----
From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Bob McGraw
- K4TAX
Sent: Thursday, July 10, 2014 3:20 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Reasons to buy an OM7 instead of an Eagle

Well Rick as you know, I have both on the desk.

The Eagle receiver is somewhat better.  How much well with the optional
filters in the Omni VII and both used for CW, I perceive one would find it
necessary to have both radios and the ability to switch between the two to
discern much if any difference. Sherwood Engineering has the Eagle Dynamic
range Narrow spaced measured at 90 dB while the Omni VII is measured at 80
dB.  Rob also stated that most hams will find the 80 dB performance most
adequate.

However, per Sherwood Engineering Receiver report, the Noise floor on the
Omni VII is -130 & -140 dBm while the noise floor on the Eagle is -124 &
-132 dBm.

The display on the Omni VII is much easier to see and read plus it gives
more information and one can see the S meter  {Rick}.

The S meter on the Omni VII goes to 60 dB over S-9 while the S meter on the
Eagle goes to 30 dB over S-9.

The S meter on the Eagle shows only signal strength and SWR. The S meter on
the Omni VII shows signal strength and is user selectable between PWR out
and SWR.

The Eagle has dual concentric knobs for AF gain and RF gain and another set
for PBT and BW.  The Omni VII has one knob that has a momentary push in to
toggle between the two functions.

The Omni VII had separate RIT and XIT buttons and displays. The Eagle had
only a RIT function which is difficult to read the value on the display.

The Omni VII has a CW spot function.  The Eagle does not.

The Eagle has a hardware Noise Blanker. The Omni VII has a firmware Noise
Blanker.

The Eagle DSP BW works nicely down to 100 Hz while the Omni VII DSP BW only goes to 200 Hz. For both radios, any optional filters automatically switch
in the RX path as the respective BW is selected.

The Omni VII RX BW is adjustable up to 12 KHz standard.  The Eagle BW
adjustable up to the widest roofing filter installed.

The MENU on the Omni  VII is accessed by a MENU button on the front panel.
The Eagle Config Menu must start with the power off, hold down FNC and then
turn power on.

The KEY jack on the Omni VII is on the front and is a 1/4" TRS connector.
The KEY jack on the Eagle is on the rear and is a 1/8" TRS connector.

The EXT SPKR jack on the Omni VII is on the rear and is a 1/4" TR connector.

The EXT SPKR jack on the Eagle is on the rear and is a 1/8" T R connector.

The Omni  VII has a dedicated button for TUNE and PWR while the Eagle one
must use the FNC before accessing the PWR function.

The Eagle is controlled externally via USB communications port.  The Omni
VII is controlled externally by a RS-232 port.

The Omni VII has a direct internet connection.  The Eagle does not offer
this feature.

The Omni VII offers two ANT port plus a separate RX ANT port.  The Eagle
only offers a single ANT port.

The Omni VII offers direct frequency entry. The Eagle does not have direct
frequency entry.

The Omni VII can switch direct to any band with the push of a button.  The
Eagle must cycle through several bands to get to the others.

The ATU is much faster to resolve a match with the Omni VII.  The Eagle
takes a bit longer to resolve a match. Both radios ATU will match a 10:1 SWR
or better.

The Eagle is about 1/4 the size of the Omni VII




I could do three or four pages of this stuff. How much more do you want or

need?    Best bet, just download both manuals from the Tentec website and
read them.

73
Bob, K4TAX




----- Original Message -----
From: "Rick - DJ0IP / NJ0IP" <Rick@DJ0IP.de>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Wednesday, July 09, 2014 4:10 PM
Subject: [TenTec] Reasons to buy an OM7 instead of an Eagle


I was just asked off list for reasons to warrant spending the extra bread
on
an OM7 instead of an Eagle.
Ha! I had to bite my tongue to keep from saying "none, there aren't any!"
(hi)

There are of course 2 or 3 minor reasons and I've created my list below.
Perhaps someone else more familiar with the OM7 than I am can think of
other
reasons that I have forgotten.
Grateful to any additional tips.

(and to the OM who asked me this question, if you do not subscribe to the
tentec group at contesting.com, send me another email and I will forward
you
any replies we get).
==========================================================

Hi OM, (name withheld)

You do realize of course that you have posed that question to a man in
love
with his Eagle!  (hi)
OK, but I will try and be objective on this.

The Eagle's better receiver is really only noticeable in BIG contests
where
a good operator is willing to dive into the middle of the heaviest pile-up on the band to work whatever DX multiplier is under all the rumble. Apart from that, there is not a lot of difference in the two receivers. However
when the going gets tough, the Eagle will outshine the Omni 7.

I'll start with the only other negative of the OM7 over the Eagle: it has
only one knob for AF and RF gain.  Not the end of the world but separate
knobs would have been better.

And of course if you go backpacking, I'd rather carry an Eagle!  (hi)
Same applies for mobile operations.

Now here is my short list of features the OM7 has which the Eagle does
not:

. A larger read out, including an S-Meter that you can actually see and
read

. Better interfacing to old amplifiers (or new Ameritron amplifiers) in CW
mode.  The OM7 has adjustable hang delay on the tail end of the signal.
The
Eagle does not have this feature and if you have one of these amps, you
absolutely need it.  With the Eagle, you must purchase the Model 318 Amp
Keyer for a hundred bucks.

. Interfacing to Ten-Tec full QSK amplifiers (dual-cable keying).  The
Eagle
does not have this.  If you don't have a full QSK linear with this keying
loop circuitry, it doesn't matter.

. A band scope (though it's not the greatest)

. Larger heat sink on the back side for cooling the final transistors.
You
really do not need a fan unless you are running RTTY.  The Eagle doesn't
have this so it must rely on a fan. It is not terribly loud but it is
audible.

. Direct frequency entry keypad

. Curtis mode A and B keying. It's fixed on the Eagle, but I have no idea
which one.  Somehow I never paid any attention to that stuff.  I just key
whatever they throw at me and it somehow seems to always work.

. Two spare RCA phono plugs AND an internal provision to connect two coax
cables to these to be used as connection for a pre-selector or noise
cancelor.

. A serial port.

. Connection for the POD (the remote VFO knob).  I sometimes miss this on
my
Eagle.

. 2 antenna jacks

. Ethernet connection

. AUX RX (antenna) - an input for a receive-only antenna (uses one of the
two ANT connections)

. Adjustable bandwidth on SSB

. Adjustable RX and TX equalizers

. CTCSS for FM

. Adjustable CW (keying) weighting

. SPOT (for spotting in CW) - which I personally feel is worthless

. Adjustable rise/fall time on CW.  A fancy option but I don't feel it is
necessary.  The Eagle's CW signal is just fine.

. FSK X Data (if you are into RTTY)

. VFO Speed Shift which basically speeds up the tuning rate by a factor of

4
when you turn the VFO knob real fast.  Many people like this feature a
lot.

. A very comfortable software menu (probably the very best in the
industry)

. OmniRig support (very important for many 3rd party software programs)

. A dedicated RIT/XIT knob (using the RIT on the Eagle is very clumsy)

. And of course REMOTE CONTROL (over the Internet)

That's all that comes to mind right now, but keep in mind that I do not
own
an OM7 and the last time I even saw or used one was in 2007.  That was 7
years ago. and my old grey cells "ain't what they used to be".

73 - Rick, DJ0IP
(Nr. Frankfurt am Main)



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>