Amps
[Top] [All Lists]

Re: [Amps] Tube swap

To: amps@contesting.com
Subject: Re: [Amps] Tube swap
From: "Roger (K8RI)" <k8ri@rogerhalstead.com>
Date: Wed, 29 Jan 2014 02:03:14 -0500
List-post: <amps@contesting.com">mailto:amps@contesting.com>
On 1/28/2014 6:11 PM, Carl wrote:The handbook has a good section on designing them, but after you get all the info, and calculations, you have to take into account stray inductance and capacitance. IE, they give you a base design that likely will need to be modified to fit the layout of the amp and tube, or tube. So as Cars says, pick an amp with the same tube and similar lauot and build a supressor like theirs and it'll likely work with little or no modification.

73

Roger (K8RI)


Suppressors are usually tube and layout/construction dependent for the
inductor part.

Look at commercial and good HB ham amps that have the tube you want to
use and go from there.

Having a quality brand of GDO helps a lot as an economical tool..

Carl
KM1H


----- Original Message ----- From: "Karel" <kebenstr@bmts.com>
To: "Carl" <km1h@jeremy.mv.com>; <donroden@hiwaay.net>;
<amps@contesting.com>
Sent: Tuesday, January 28, 2014 5:53 PM
Subject: Re: [Amps] Tube swap


Thanks Carl,
I just have to figure out what the factory design should be. I will
definitely use ceramic resistor. Any suggested lead to better
suppressor setup?
Values, arrangement? Thanks,
Karel, VA3KO

----- Original Message ----- From: "Carl" <km1h@jeremy.mv.com>
To: "Karel" <kebenstr@bmts.com>; <donroden@hiwaay.net>;
<amps@contesting.com>
Sent: Tuesday, January 28, 2014 4:26 PM
Subject: Re: [Amps] Tube swap


Stick to factory designs, they work fine for decades without problems.
The Ohmite OY series of ceramic resistors do well in place of out of
tolerance carbon composition.

Sell the voodoo crap on fleabay to a CBer

Carl
KM1H


----- Original Message ----- From: "Karel" <kebenstr@bmts.com>
To: <donroden@hiwaay.net>; <amps@contesting.com>
Sent: Tuesday, January 28, 2014 2:36 PM
Subject: Re: [Amps] Tube swap


Sorry, I met him over internet right after his write-up for AR
Handbook was rejected and that was a long time ago. I brought up his
name here once before and got slapped for it, sorry, I should know
by now. I owe cup of coffee to all. Hopefully we will meet some day.

I still have his suppressor package for two 4-1000A 's to be
installed. Without bringing his name out again, can someone warn me
about using it?

I installed his suppressor package on my friend's Henry 2K. It
lasted few years, but his plate transformer croaked recently, I
wonder if the suppressor had anything to do with that.

Karel Ebenstreit, VA3KO

----- Original Message ----- From: <donroden@hiwaay.net>
To: <amps@contesting.com>
Sent: Tuesday, January 28, 2014 10:56 AM
Subject: Re: [Amps] Tube swap


Quoting Karel <kebenstr@bmts.com>:

Hardy,
yes I made myself a Hi-pot tester as well. I forgot the specs, but
I believe I can go up to 20 kV. (It may be one of Richard Measures
designs).




Unwritten Amps Rule # 1

Never invoke the name of the witchdoctor.

You owe everyone a cup of coffee.


Don W4DNR

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps


-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3681/7039 - Release Date:
01/28/14





-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2014.0.4259 / Virus Database: 3681/7041 - Release Date: 01/28/14


_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps




---
This email is free from viruses and malware because avast! Antivirus protection 
is active.
http://www.avast.com


_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>