On 1 Mar 2014 at 23:14, Rick - DJ0IP / NJ0IP wrote:
> "Dip" was pre-watt meter days.
> No need to dip anymore.
>
> Just tune for maximum smoke!
Rick - DJ0IP / NJ0IP ALSO wrote:
> this is always subject to the
Ig not exceeding max specs.
And yes of course Rick - that is precisely why we dip Ip first before
everything else,
and always watch for not exceeding maximum plate current rating as well as
maximum Ig rating.
My Centurion 442 wants to get back on the air... but it is waiting patiently
to be
dipped and peaked again when the rewound plate transformer arrives back home!
YMMV - de AF4K, Bry
> Precisely, running full drive power, you first tune the PLATE for max smoke,
> then repeat the sequence of slowly advancing the LOAD and peaking the PLATE
> for max smoke.
> If you reach the point where increasing the LOAD and peaking the plate
> brings no more increase in max smoke, but just an increase in Ig, then
> you've gone too far. Back it off.
>
> The idea is to find the exact point where max smoke is reached with min LOAD
> that can achieve it - and of course all of this is always subject to the Ig
> not exceeding max specs.
>
> Piece of cake.
>
> The only thing I do different in practice is, I first tune for max smoke
> with about 30w of drive, just to get everything in resonance, then I proceed
> as described above.
>
> Dip? 40 years ago, maybe!
>
> 73 - Rick, DJ0IP
> (Nr. Frankfurt am Main)
>
>
> -----Original Message-----
> From: TenTec [mailto:tentec-bounces@contesting.com] On Behalf Of Bob McGraw
> - K4TAX
> Sent: Saturday, March 01, 2014 10:00 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] In praise of older technology
>
> The only thing I ever "dip" is a little chew.
>
> 73
> Bob, K4TAX
>
>
> ----- Original Message -----
> From: "Brian Carling" <bcarling@cfl.rr.com>
> To: "Ed Purvis" <wa4njy@yahoo.com>; "Discussion of Ten-Tec Equipment"
> <tentec@contesting.com>
> Sent: Saturday, March 01, 2014 2:18 PM
> Subject: Re: [TenTec] In praise of older technology
>
>
> > Ed you must be talking about those XE stations tuning up on SSB on the low
>
> > end of 40m. They groan "hoooooo-la" while they dip the plate control !
> > SOP
> >
> > Best regards - Bry Carling
> >
> >
> >
> >> On Feb 22, 2014, at 8:29 PM, Ed Purvis <wa4njy@yahoo.com> wrote:
> >>
> >> There are some on hi-fi sideband that I am not sure they are talking or
> >> their stomach is making noise.
> >>
> >>
> >>
> >>
> >>
> >>
> >> ________________________________
> >> From: Steve Berg <wa9jml@frontier.com>
> >> To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
> >> Sent: Saturday, February 22, 2014 8:12 PM
> >> Subject: Re: [TenTec] In praise of older technology
> >>
> >>
> >>
> >>
> >> As part of my collection, I have Drake 2B receiver and a Gonset GSB100
> >> phasing exciter. One night I wound up in a round table with a bunch of
> >> HiFi SSB aficionados 0n 40 meters. These guys were running advanced
> >> equalizers and high-end microphones. Then had the latest Oriental
> >> Transceivers. They even had audio spectrum analyzers to check out each
> >> others signals. So, I asked for an evaluation, and they were quite
> >> complimentary. So, they asked what I was running, and I told them a
> >> 1957 vintage phasing exciter with a D104 mic. They were amazed! Sure,
> >> it drifts, and it is hard to get it right on frequency by zerobeating
> >> the receiver BFO with the carrier on the exciter. But it is a lot of
> >> fun to use.
> >>
> >> Steve WA9JML
> >>
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/tentec
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|