Carl,
Thanks very much for the info on the voice synthesizer board on my Omni VI +.
I jumped the diode as you described and it worked!
Thanks again.
73’s
Rich, WD6DOK
> On Mar 9, 2016, at 9:55 AM, Froiseth Richard <rfwd6dok@centurylink.net> wrote:
>
> Carl,
>
> Thanks for the info.
> I wrote Ten Tec a note and they wont give out any info without a work order.
> I use to be able to call and receive help on things like this, but I guess
> times have change.
> Thanks again.
>
> 73’s
> Rich, WD6DOK
>
>
>
>
>
>
>
>> On Mar 9, 2016, at 9:50 AM, Carl Winkles <jcwinks@att.net> wrote:
>>
>> Here is what Ten Tec told me years ago: "If there is a diode just to the
>> left of the MC74HC573 chip (third connection on the left edge of the card)
>> place a jumper across it. Depending on the model of the rig, there will be
>> one diode, two diodes or a jumper. The Omni series requires a jumper for
>> proper readout. '
>>
>> I don't remember having any problem doing this, and I remember that it
>> worked. Hope this helps.
>>
>> Carl, K4SEV
>>
>> Enviado desde mi iPhone
>>
>>> El mar 9, 2016, a las 1:56 AM, Froiseth Richard <Rfwd6dok@centurylink.net>
>>> escribió:
>>>
>>> Mike,
>>>
>>> Thanks for responding to my question.
>>> I bought the Omni VI + from Ten Tec a few years ago and the radio came with
>>> the board installed.
>>> There were some things going on in my life at that time and I didn’t have a
>>> chance to check out the board or the rest of the radio. I know that sounds
>>> silly, but that's what happened, anyway do you know if you can tell if the
>>> mod has been done by looking at the board? There is a note in the manual
>>> stating if the board came out of anything other than a 563 or 564 call the
>>> factory for modification details. I guess I can shoot them off an e-mail
>>> and hope they respond.
>>> I was hoping that someone on here could answer my question.
>>>
>>>
>>> 73’s
>>> Rich, WD6DOK
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>> On Mar 8, 2016, at 6:25 PM, Mike Bryce <prosolar@sssnet.com> wrote:
>>>>
>>>> silly question, but did this start to act up or did you buy a voice card
>>>> and add it to the radio?
>>>>
>>>> There is a modification that needs to be done to the card if it came out
>>>> of the paragon and into the Omni V/VI. I don’t recall what it was, but it
>>>> was rather simple
>>>>
>>>> mike, wb8vge
>>>>
>>>>
>>>> Mike, WB8VGE
>>>> SunLight Energy Systems
>>>> The Heathkit Shop
>>>> http://www.theheathkitshop.com/ <http://www.theheathkitshop.com/>
>>>> J e e p
>>>> o|||||||o
>>>>
>>>> A man with one clock knows what time it is. A man with two clocks is never
>>>> sure.
>>>>
>>>>
>>>>
>>>>> On Mar 8, 2016, at 4:45 PM, Froiseth Richard <rfwd6dok@centurylink.net>
>>>>> wrote:
>>>>>
>>>>> I have an Omni VI + with the Voice Synthesizer Board #257 installed.
>>>>> When I press the voice button on the front of the radio the voice
>>>>> announces the following:
>>>>>
>>>>> 80m, 40m announces 29731 no matter where you are tuned.
>>>>> 12m, 15m and 20m announces 429731 no matter where you are tuned.
>>>>>
>>>>> My understanding is the board should announce the freq. you are presently
>>>>> tuned.
>>>>>
>>>>> Can anyone shed some light on this problem?
>>>>>
>>>>> 73’s
>>>>> Rich, WD6DOK
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>> On Mar 2, 2016, at 5:09 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:
>>>>>>
>>>>>> Don't use the 500hz and 250hz filters. Put an Inrad #762 600hz filter in
>>>>>> the 1000hz slot: http://users.vnet.net/btippett/inrad_.htm
>>>>>>
>>>>>> 73, Barry N1EU
>>>>>>
>>>>>>> On Wed, Mar 2, 2016 at 11:57 PM, Tim Wininger <ky5rtim@gmail.com> wrote:
>>>>>>>
>>>>>>> Anyone have one or all of these filters excess to your needs. Looking
>>>>>>> for
>>>>>>> the TT versions or Inrad versions.
>>>>>>>
>>>>>>> Thanks for any info,
>>>>>>>
>>>>>>> Tim , AB4B
>>>>>>> Rogersville ,AL
>>>>>>> 35652
>>>>>>> _______________________________________________
>>>>>>> TenTec mailing list
>>>>>>> TenTec@contesting.com
>>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>> _______________________________________________
>>>>>> TenTec mailing list
>>>>>> TenTec@contesting.com
>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>>
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|