John,
You will have a polling system soon? Please provide more details?
Thanks,
Dan
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]
> On Behalf Of John Tully
> Sent: Wednesday, April 28, 2004 9:59 AM
> To: Karlnet Mailing List
> Subject: RE: [Karlnet] Bridge and route on the same KN200
>
> At 02:35 PM 4/28/2004, you wrote:
> >John,
> >
> >Have you thought about supporting the KN PC Driver for Linux so you
can
> >setup a Satellite station off a KN TC network?
>
> For 2.4GHz solutions, most people use our AP only and use some low
cost
> client solution -- unless they need a very smart router at the client,
and
> then they use our client solution also. For 5GHz, people use all
MikroTik
> RouterOS products (and usually www.routerboard.com products) for a
> complete
> high speed solution.
>
> So, I don't think it would be so useful to have KN TC 2.4GHz client
only
> support in our system. If the Linux driver includes source, then it
> wouldn't be difficult to add it -- but are many people interested in
this?
>
> Also, we will have the so called 'polling' feature soon -- and from
what I
> know about the Karlnet TC, ours will have some important features that
are
> not in the TC. For example, ours will use multiple rates (actually,
ours
> uses the best rate for throughput) -- where I have read that with
some/all
> TC versions you have to set only one rate for the AP. Of course I am
not
> an expert on TC, so I may be wrong.
>
> John
>
>
> >-----Original Message-----
> >From: karlnet-bounces@WISPNotes.com
> >[mailto:karlnet-bounces@WISPNotes.com] On Behalf Of John Tully
> >Sent: Wednesday, April 28, 2004 2:56 AM
> >To: Karlnet Mailing List
> >Subject: Re: [Karlnet] Bridge and route on the same KN200
> >
> >You can do that with a MikroTik RouterOS AP.
> >http://www.mikrotik.com/docs2.8/interface/bridge.main
> >
> >John
> >www.mikrotik.com
> >
> >At 06:15 PM 4/27/2004, you wrote:
> > >It's a shame that with 4 interfaces on the KN-200 that you can't
define
> >L2
> > >bridge groups - For example, define Interfaces 1 & 2 as "Group 1"
and
> > >Interfaces 3 & 4 as "Group 2" so that you can then route between
Group
> >1 &
> > >Group 2.
> > >
> > >*********** REPLY SEPARATOR ***********
> > >
> > >On 2004-04-26 at 10:34 PM Paul Horak wrote:
> > >
> > > >Anybody know if you can bridge and route on the same
> > > >radio (KN200 in this rather bizarre case :-))? If so,
> > > >please can you share the config? Turning on routing
> > > >seems to automatically deny bridging of IP traffic.
> > > >
> > > >Cheers,
> > > >
> > > >Paul
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >__________________________________
> > > >Do you Yahoo!?
> > > >Win a $20,000 Career Makeover at Yahoo! HotJobs
> > > >http://hotjobs.sweepstakes.yahoo.com/careermakeover
> > > >_______________________________________________
> > > >Karlnet mailing list
> > > >Karlnet@WISPNotes.com
> > > >http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> > >
> > >
> > >_______________________________________________
> > >Karlnet mailing list
> > >Karlnet@WISPNotes.com
> > >http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> >_______________________________________________
> >Karlnet mailing list
> >Karlnet@WISPNotes.com
> >http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> >_______________________________________________
> >Karlnet mailing list
> >Karlnet@WISPNotes.com
> >http://lists.wispnotes.com/mailman/listinfo/karlnet
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> --
> [This E-mail scanned for viruses by Declude Virus]
>
--
[This E-mail scanned for viruses by Declude Virus]
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
|