Also running 2.056 and the Remote I/O works fine. I find that I have to
have the sub receiver's audio either muted or turned off so not to mix
with the desired audio on the main.
I am using a microHam microkeyer for my I/O and audio switching with
numerous programs.
Robb, NØRU
----- Original Message -----
From: "Larry Menzel" <retire@means.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, March 27, 2006 8:28 PM
Subject: Re: [TenTec] Orion Aux Audio output
My apologies, guys, I'm still running 2.055. Intended to load .056 but
haven't done so...may not if this is persistant.
I do not see this with 2.055. Buck, maybe you want to revert and see if
the
problem persists.
Larry, N0XB
----- Original Message -----
From: "Barry Gross" <barry.n1eu@gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, March 27, 2006 7:20 PM
Subject: Re: [TenTec] Orion Aux Audio output
On my v2.056 Orion, the aux I/O "line" outputs definitely vary (almost
linearly) with the main/sub af controls.
73,
Barry N1EU
On 3/28/06, Larry Menzel <retire@means.net> wrote:
Hi, Buck,
Well, I"m running RTTY with 2.056, with no problem, using the AUX I/O.
I
set the volume to the program with the volume control for the soundcard.
The front control has no function on the I/O. Are you sure you have the
TX
Audio Source in the SSB menu set to AUX and not MIC or BOTH? Then pull
up
in Windows START>All Programs>Accessories>Entertainment>Volume Control
and
make sure your LINE IN is enabled, or easier yet just click on the
volume
control in the lower right of your monitor. If you're hooked up
correctly,
LINE-IN will control the volume to the soundcard from the AUX OUT plug
on
the radio.
It is possible that you're simply using the sound from the speaker
through
your microphone to drive the software, because the TX Audio Source is
set
to
mic or both.
Hope this helps...or call me at 952 212 2664
Larry, N0XB
----- Original Message -----
From: <K4IA@aol.com>
To: <tentec@contesting.com>
Cc: <ditsnbits@tentec.com>
Sent: Sunday, March 26, 2006 11:27 PM
Subject: [TenTec] Orion Aux Audio output
>I have been trying to get back into digital modes and notice that the
audio
> output from the AUX I/O connector pin 4 seems to depend on the volume
> control
> instead of being a line out as described in the manual and as it
operated
> prior to ver 2.
>
> This is maddening because it means you have to turn up the volume and
> listen
> to the warbling. Before you could turn down the volume and just
> watch
> the
> screen.
>
> Anyone else notice this?
>
> K4ia "Buck"
> Fredericksburg, Virginia USA
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|