Re: [TenTec] having problem getting amp to work with Orion II

["John" <fraz1@bellsouth.net>]

John....just checking the obvious.  On the back of the O II, the TX en and 
out are in the vertical plane.  IE, one above the other.  Make sure you have 
the both cables under the same keying loop (either 1 or 2).
73 W4II
----- Original Message ----- 
From: "John Molenda" <brazos@rochester.rr.com>
To: <ac5aa@ac5aa.com>; "Discussion of Ten-Tec Equipment" 
<tentec@contesting.com>
Sent: Monday, March 22, 2010 6:02 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II


> roger coax connected
> ----- Original Message ----- 
> From: "Duane Calvin" <ac5aa1@gmail.com>
> To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
> Sent: Monday, March 22, 2010 6:51 PM
> Subject: Re: [TenTec] having problem getting amp to work with Orion II
>
>
> > Oops - three cables - don't forget the exciter RF!  :-)
> >
> > Duane Calvin, AC5AA
> > Austin, Texas
> > www.ac5aa.com
> >
> >
> > -----Original Message-----
> > From: tentec-bounces@contesting.com 
> > [mailto:tentec-bounces@contesting.com]
> > On Behalf Of John
> > Sent: Monday, March 22, 2010 5:35 PM
> > To: Discussion of Ten-Tec Equipment
> > Subject: Re: [TenTec] having problem getting amp to work with Orion II
> >
> > That is correct John!
> >
> > 73 John W4II
> > ----- Original Message ----- 
> > From: "John Molenda" <brazos@rochester.rr.com>
> > To: "aa4nn" <aa4nn@earthlink.net>; "Discussion of Ten-Tec Equipment"
> > <tentec@contesting.com>
> > Sent: Monday, March 22, 2010 5:19 PM
> > Subject: Re: [TenTec] having problem getting amp to work with Orion II
> >
> >
> > > I have reread the manual and looked at the hookup my question is this
> > > (when
> > > hooking Orion II to titan III amp ) there are only two cables to run
> > > between
> > > the two tx en out  key in out .  and then use the switch on the amp in
> > > qsk
> > > mode .  then go to the tx menu and enable loop 1 .  is this correct am I
> > > missing a hookup ?  thanks John kb2huk
> > > ----- Original Message ----- 
> > > From: "aa4nn" <aa4nn@earthlink.net>
> > > To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> > > Sent: Monday, March 22, 2010 9:14 AM
> > > Subject: Re: [TenTec] having problem getting amp to work with Orion II
> > >
> > >
> > > > Does the term QSK or PTT ring a bell?
> > > > de Joe, aa4nn
> > > > Lake Wylie, SC
> > > > ------------------------------------------------------
> > > > > > Hello all , I am having a problem getting my Orion II to work with my
> > > > > > Titan III
> > > > _______________________________________________
> > > > TenTec mailing list
> > > > TenTec@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/tentec
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > ----------------------------------------------------------------------------
> > ----
> >
> >
> >
> > No virus found in this incoming message.
> > Checked by AVG - www.avg.com
> > Version: 8.5.437 / Virus Database: 271.1.1/2763 - Release Date: 03/22/10
> > 07:33:00
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

--------------------------------------------------------------------------------



No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2763 - Release Date: 03/22/10 
07:33:00