Just make sure you do not have TXEN and TXOUT cables reversed. If you do
you would have the symptom you see.
Carl Moreschi N4PY
121 Little Bell Drive
Hays, NC 28635
www.n4py.com
----- Original Message -----
From: "John Molenda" <brazos@rochester.rr.com>
To: "N4PY2" <n4py2@earthlink.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Tuesday, March 23, 2010 4:18 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
Yes , it is only when I put the amp in operate that I see no output on the
meter ( antenna tuner meter or amp meter ) If I have the amp connected to
the radio and the menu set and the switch on the amp is on standby and
when
I key up there is power out if I stop there and push the switch to operate
and key it up there is no output . JOhn kb2huk
----- Original Message -----
From: "N4PY2" <n4py2@earthlink.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Tuesday, March 23, 2010 4:10 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
It sounds like the amp does not connect TXEN to TXOUT when its antenna
relay
switches to transmit. If you have the amp in standby but still connected
to
TXEN and TXOUT, does the Orion transmit normally with the keying loop
enabled?
Carl Moreschi N4PY
121 Little Bell Drive
Hays, NC 28635
www.n4py.com
----- Original Message -----
From: "John Molenda" <cdistflatfoot@gmail.com>
To: "N4PY2" <n4py2@earthlink.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Tuesday, March 23, 2010 3:01 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
Hi Carl , thanks for the quick response , yes the Orion will show power
out
on my meter when the tx en and tx out are jumpered together and the key
loop is on and amp key tracks is on the keying loop setting . so you
think
the problem is with the amp . thanks John kb2huk----- Original
Message -----
From: "N4PY2" <n4py2@earthlink.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Tuesday, March 23, 2010 2:51 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
John,
What I'm trying to do is diagnose what is going on. If you turn on the
Orion keying loop and do not connect anything between TXEN and TXOUT,
transmit will be blocked. If you then jumper TXEN and TXOUT together
without the amp connected, the Orion should work alone and normally.
So,
does this work this way? If this does, then the problem is in the amp.
If
it doesn't, then the problem is in the Orion.
Carl Moreschi N4PY
121 Little Bell Drive
Hays, NC 28635
www.n4py.com
----- Original Message -----
From: "John Molenda" <cdistflatfoot@gmail.com>
To: "N4PY2" <n4py2@earthlink.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Tuesday, March 23, 2010 2:24 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
carl could you please clairify #2 thanks John
----- Original Message -----
From: "N4PY2" <n4py2@earthlink.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, March 22, 2010 10:32 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
John,
>
1) Turn on TXloop for antenna 1 on the orion.
2) Connect TXEN to TXOUT on the Orion.
Does the Orion now key when you try to transmit? It should.
If that works, then connect TXOUT to the Titan key in. Connect the
Titan
key out to the Orion TXEN. The Orion should still key. So exactly
what
does not work.
Carl Moreschi N4PY
121 Little Bell Mountain Dr
Hays, NC 28635
www.n4py.com
Try this:
----- Original Message -----
From: "John Molenda" <cdistflatfoot@gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, March 22, 2010 9:15 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion
II
I just check continuity of the two rca plugs and the coax it checks
out
good
. John kb2huk
----- Original Message -----
From: "John Molenda" <brazos@rochester.rr.com>
To: <ac5aa@ac5aa.com>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Monday, March 22, 2010 7:02 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion
II
roger coax connected
----- Original Message -----
From: "Duane Calvin" <ac5aa1@gmail.com>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Monday, March 22, 2010 6:51 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion
II
Oops - three cables - don't forget the exciter RF! :-)
Duane Calvin, AC5AA
Austin, Texas
www.ac5aa.com
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]
On Behalf Of John
Sent: Monday, March 22, 2010 5:35 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] having problem getting amp to work with
Orion
II
That is correct John!
73 John W4II
----- Original Message -----
From: "John Molenda" <brazos@rochester.rr.com>
To: "aa4nn" <aa4nn@earthlink.net>; "Discussion of Ten-Tec
Equipment"
<tentec@contesting.com>
Sent: Monday, March 22, 2010 5:19 PM
Subject: Re: [TenTec] having problem getting amp to work with
Orion
II
I have reread the manual and looked at the hookup my question is
this
(when
hooking Orion II to titan III amp ) there are only two cables to
run
between
the two tx en out key in out . and then use the switch on the
amp
in
qsk
mode . then go to the tx menu and enable loop 1 . is this
correct
am
I
missing a hookup ? thanks John kb2huk
----- Original Message -----
From: "aa4nn" <aa4nn@earthlink.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, March 22, 2010 9:14 AM
Subject: Re: [TenTec] having problem getting amp to work with
Orion
II
Does the term QSK or PTT ring a bell?
de Joe, aa4nn
Lake Wylie, SC
------------------------------------------------------
Hello all , I am having a problem getting my Orion II to work
with
my
Titan III
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
----------------------------------------------------------------------------
----
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2763 - Release Date:
03/22/10
07:33:00
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|