John,
Try this:
1) Turn on TXloop for antenna 1 on the orion.
2) Connect TXEN to TXOUT on the Orion.
Does the Orion now key when you try to transmit? It should.
If that works, then connect TXOUT to the Titan key in. Connect the Titan
key out to the Orion TXEN. The Orion should still key. So exactly what
does not work.
Carl Moreschi N4PY
121 Little Bell Mountain Dr
Hays, NC 28635
www.n4py.com
----- Original Message -----
From: "John Molenda" <cdistflatfoot@gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, March 22, 2010 9:15 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
I just check continuity of the two rca plugs and the coax it checks out
good
. John kb2huk
----- Original Message -----
From: "John Molenda" <brazos@rochester.rr.com>
To: <ac5aa@ac5aa.com>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Monday, March 22, 2010 7:02 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
roger coax connected
----- Original Message -----
From: "Duane Calvin" <ac5aa1@gmail.com>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Monday, March 22, 2010 6:51 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
Oops - three cables - don't forget the exciter RF! :-)
Duane Calvin, AC5AA
Austin, Texas
www.ac5aa.com
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]
On Behalf Of John
Sent: Monday, March 22, 2010 5:35 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] having problem getting amp to work with Orion II
That is correct John!
73 John W4II
----- Original Message -----
From: "John Molenda" <brazos@rochester.rr.com>
To: "aa4nn" <aa4nn@earthlink.net>; "Discussion of Ten-Tec Equipment"
<tentec@contesting.com>
Sent: Monday, March 22, 2010 5:19 PM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
I have reread the manual and looked at the hookup my question is this
(when
hooking Orion II to titan III amp ) there are only two cables to run
between
the two tx en out key in out . and then use the switch on the amp in
qsk
mode . then go to the tx menu and enable loop 1 . is this correct am
I
missing a hookup ? thanks John kb2huk
----- Original Message -----
From: "aa4nn" <aa4nn@earthlink.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, March 22, 2010 9:14 AM
Subject: Re: [TenTec] having problem getting amp to work with Orion II
Does the term QSK or PTT ring a bell?
de Joe, aa4nn
Lake Wylie, SC
------------------------------------------------------
Hello all , I am having a problem getting my Orion II to work with
my
Titan III
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
----------------------------------------------------------------------------
----
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.437 / Virus Database: 271.1.1/2763 - Release Date: 03/22/10
07:33:00
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|