Are you using PTT to key the rig with fldigi? With WSJT-X, I've tried
using CAT with my Omni VI and I can't get it to work right. It will key
the rig when I select "test CAT" but it won't unkey until I close the
program. Maybe Winlink is trying to use CAT and should be using PTT?
I use the default CIV address of 04, 19200 for the baud rate and a home
made computer interface which key the rig when RTS goes high.
hth
73
Stan
KM4HQE
On 03/04/2018 07:12 AM, Joe Papworth via TenTec wrote:
Hmmm...
I run MMTTY and FLFigi on that same PC over the same connection and they key
the Omni VI Plus fine.
Those work but WinLink/Winmor does not, so it's gotta be something in the
program or a setting in it.
Later, Joe, K8MP
Sent from AOL Mobile Mail
-----Original Message-----
From: Carl Moreschi <n4py3@earthlink.net>
To: k8mp <k8mp@aol.com>
Cc: tentec <tentec@contesting.com>
Sent: Sun, Mar 4, 2018 06:54 AM
Subject: Re: [TenTec] I surrender
I don't think the Omni VI implemented that command.
Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
<a href="http://www.n4py.com"; target="_blank">www.n4py.com</a>
On 3/4/2018 12:06 AM, <a href="mailto:k8mp@aol.com";>k8mp@aol.com</a> wrote:
They're talkin' Carl. The rig accepts the mode and QRG commands from the
PC but apparently it doesn't accept the command to xmit.
Sent from AOL Mobile Mail
-----Original Message-----
From: Carl Moreschi <<a
href="mailto:n4py3@earthlink.net";>n4py3@earthlink.net</a>>
To: Discussion of Ten-Tec Equipment <<a
href="mailto:tentec@contesting.com";>tentec@contesting.com</a>>
Sent: Sat, Mar 3, 2018 11:12 PM
Subject: Re: [TenTec] I surrender
There's 3 things that have to match.
Baud rate (probably 1200 but might not be )
CIV address (should be 04 )
Correct comport number.
If all those match it will work.
Carl Moreschi N4PY
58 Hogwood Rd
Louisburg, NC 27549
<a href="http://www.n4py.com"; target="_blank">www.n4py.com</a> <<a href="http://www.n4py.com";
target="_blank">http://www.n4py.com</a>>
On 3/3/2018 10:32 PM, Joe Papworth via TenTec wrote:
> Gents,
>
> <div>I threw in the towel on making WinLink and Winmor work with my
Omni VI Plus. I have WinLink working over our local Mesh network and I
was hoping get it working on HF but no dice.
>
> Thank you Carl, Rod, Greg, and others who weighed in.
>
> Joe, K8MP
>
> Sent from AOL Mobile Mail</div>
> _______________________________________________
> TenTec mailing list
> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a> <<a
href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
> <a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>
_______________________________________________
TenTec mailing list
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a> <<a
href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
<a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|