TenTec
[Top] [All Lists]

Re: [TenTec] I surrender

To: lee@wa3fiy.com, tentec@contesting.com
Subject: Re: [TenTec] I surrender
From: Joe Papworth via TenTec <tentec@contesting.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Sun, 4 Mar 2018 11:18:52 -0500
List-post: <mailto:tentec@contesting.com>
Aha! So it does work!

What rig did you choose from the Radio Set-up? The two generic-sounding Icom 
choices talk to the Omni VI for freq and mode but they don't key it.
Carl suggested that there may not be a keying command, per se, so maybe they're 
toggling something else in FLDigi and MMTTY.

I'm looking at the FLDigi rig control set up and that one has Omni VI in its 
list, so that one was a no-brainer. (How lucky for me).
I noticed there's a check box that says "PTT via HamLib command" (HamLib is 
what they call their list of rigs that they are pre-set-up for control)
That box is checked and it suggests to me that PTT is done via a radio command.

Regarding the PC to radio connections, I'm using a serial port for rig control 
and the Line-in/out from the PC directly to the Audio out/in on the back of the 
rig.

I'm looking at MMTTY now. It also has Omni VI Plus in its radio list, so it was 
also a no brainer.
It's interesting to note that MMTTY also shows the RX and TX command syntax. 
( \$FEFExxE01601FD\w10 for TX )

In my and Winmor TNC Setup, I just picked the PC's sound card device names from 
the drop-downs.
In the Radio set-up, I tried both of the generic Icom choices, (Changed the rig 
address to 04 to talk to the Omni)
Those both talk to the Omni, except for making it xmit.

What are your Winmor settings Lee?

Thanks, Joe



-----Original Message-----
From: Lee <lee@wa3fiy.com>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Cc: k8mp <k8mp@aol.com>; tentec <tentec@contesting.com>
Sent: Sun, Mar 4, 2018 9:24 am
Subject: Re[2]: [TenTec] I surrender

Joe,

The Omni VI works fine with Winlink Winmor. I have one here that I have 
used many times.

I assume MMTTY and fldigi are being used with the Omni. If so, then we 
know the hardware interface works so it is only a configuration issue 
with Winlink. What do you use for an interface between your computer 
and the Omni? In Winlink there are two setup screens that need 
attention, "WINMOR TNC setup" and "Radio Setup". TNC setup selects 
the sound card interface and Radio Setup selects radio control if used 
(yours appears to be working fine) and PPT control.

Can you look at the MMTTY or fldigi setup parameters to get an idea of 
what works?

73,

-Lee-

WA3FIY

Sounds like the PTT line to the Omni is not getting triggered.




>> _______________________________________________
>> TenTec mailing list
>> <a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a> <<a 
>>href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
>> <a href="http://lists.contesting.com/mailman/listinfo/tentec"; 
>>target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
>_______________________________________________
>TenTec mailing list
>TenTec@contesting.com
>http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>