WriteLog
[Top] [All Lists]

Re: [WriteLog] SIIG 4 Serial Port PCI Board and MMTTY

To: <aldewey@aol.com>, Writelog Forum <writelog@contesting.com>
Subject: Re: [WriteLog] SIIG 4 Serial Port PCI Board and MMTTY
From: Clay Melhorn <n9io@hotmail.com>
Date: Mon, 28 Sep 2009 13:10:36 -0500
List-post: <writelog@contesting.com">mailto:writelog@contesting.com>
Hi Al K0AD,

Related to your problem.

I have three desktop computers with SIIG quartet rs-232 boards.

I have never had a failure with rig control or tnc's in kiss mode.

I am about to hook my D-700A aprs radio that I have in the house

to program it from one of the desktop SIIG ports, then run Winlink from the 
same.

I will try the programming tonight to see what happens and get back to you.

The only time I haved seen a pc reboot was while programming a D-700A

from my ASUS 10" notebook from a USB to RS-232 converter (a cheapy) there are 
only usb ports on the notebook.

The notebook rebooted when writing  the program to the D-700A radio. UIView and 
rig control worked fine though.

My old P3 850mhz Sony Vaio laptop with a PCMPIA to 4 output rs-232 com port 
works perfectly when writing the same program to the D-700A.

 

As I said, I will try it tonight  on the SIIG card and get back to you with the 
results.

73'
Clay Melhorn N9IO Bonfield, IL
Webmaster:
KARS - Kankakee Area Radio Society - W9AZ http://www.w9az.com/
ARRL (Central Division) http://www.central.arrl.org/
 
 
 



 
> From: Aldewey@aol.com
> Date: Sat, 26 Sep 2009 00:27:00 -0400
> To: writelog@contesting.com
> Subject: [WriteLog] SIIG 4 Serial Port PCI Board and MMTTY
> 
> I am having trouble getting my new SIIG PCI 4 Serial Port board to key FSK.
> 
> I have a PC with one built in Serial Port. The built in serial port (at 
> COM 1) keys FSK no problem.
> 
> When I install the SIIG board, it adds COM 5, 6, 7, and 8.
> 
> I use COM 5 and 6 for Rig control with no problem. However, if I select 
> COM 7 or 8 to key FSK in MMTTY, my PC crashes and immediately re-boots. I 
> temporarily took the radio off of COM 5 and 6 and tried those for FSK - same 
> result. No matter what port I chose on the SIIG board, selecting it to key 
> FSK crashed my computer. It crashes as soon as I make the selection in RTTY
> 
> Operating System is XP.
> 
> Has anyone run into this issue? Any suggestions on what I might try?
> 
> 73,
> 
> Al, K0AD
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
                                          
_________________________________________________________________
Lauren found her dream laptop. Find the PC that’s right for you.
http://www.microsoft.com/windows/choosepc/?ocid=ftp_val_wl_290
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web:  http://www.writelog.com/

<Prev in Thread] Current Thread [Next in Thread>