Al K0AD,
As I said, I would report my findings back to you.
I tried Com 3 (S2 on the SIIG card dongle)
The Kenwood software wrote to the D-700A AOK.
Clay Melhorn N9IO Bonfield, IL
Webmaster:
KARS - Kankakee Area Radio Society - W9AZ http://www.w9az.com/
ARRL (Central Division) http://www.central.arrl.org/
> From: n9io@hotmail.com
> To: aldewey@aol.com; writelog@contesting.com
> Date: Mon, 28 Sep 2009 13:10:36 -0500
> Subject: Re: [WriteLog] SIIG 4 Serial Port PCI Board and MMTTY
>
>
> Hi Al K0AD,
>
> Related to your problem.
>
> I have three desktop computers with SIIG quartet rs-232 boards.
>
> I have never had a failure with rig control or tnc's in kiss mode.
>
> I am about to hook my D-700A aprs radio that I have in the house
>
> to program it from one of the desktop SIIG ports, then run Winlink from the
> same.
>
> I will try the programming tonight to see what happens and get back to you.
>
> The only time I haved seen a pc reboot was while programming a D-700A
>
> from my ASUS 10" notebook from a USB to RS-232 converter (a cheapy) there are
> only usb ports on the notebook.
>
> The notebook rebooted when writing the program to the D-700A radio. UIView
> and rig control worked fine though.
>
> My old P3 850mhz Sony Vaio laptop with a PCMPIA to 4 output rs-232 com port
> works perfectly when writing the same program to the D-700A.
>
>
>
> As I said, I will try it tonight on the SIIG card and get back to you with
> the results.
>
> 73'
> Clay Melhorn N9IO Bonfield, IL
> Webmaster:
> KARS - Kankakee Area Radio Society - W9AZ http://www.w9az.com/
> ARRL (Central Division) http://www.central.arrl.org/
>
>
>
>
>
>
>
> > From: Aldewey@aol.com
> > Date: Sat, 26 Sep 2009 00:27:00 -0400
> > To: writelog@contesting.com
> > Subject: [WriteLog] SIIG 4 Serial Port PCI Board and MMTTY
> >
> > I am having trouble getting my new SIIG PCI 4 Serial Port board to key FSK.
> >
> > I have a PC with one built in Serial Port. The built in serial port (at
> > COM 1) keys FSK no problem.
> >
> > When I install the SIIG board, it adds COM 5, 6, 7, and 8.
> >
> > I use COM 5 and 6 for Rig control with no problem. However, if I select
> > COM 7 or 8 to key FSK in MMTTY, my PC crashes and immediately re-boots. I
> > temporarily took the radio off of COM 5 and 6 and tried those for FSK -
> > same
> > result. No matter what port I chose on the SIIG board, selecting it to key
> > FSK crashed my computer. It crashes as soon as I make the selection in RTTY
> >
> > Operating System is XP.
> >
> > Has anyone run into this issue? Any suggestions on what I might try?
> >
> > 73,
> >
> > Al, K0AD
> > _______________________________________________
> > WriteLog mailing list
> > WriteLog@contesting.com
> > http://lists.contesting.com/mailman/listinfo/writelog
> > WriteLog on the web: http://www.writelog.com/
>
> _________________________________________________________________
> Lauren found her dream laptop. Find the PC that’s right for you.
> http://www.microsoft.com/windows/choosepc/?ocid=ftp_val_wl_290
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
_________________________________________________________________
Insert movie times and more without leaving Hotmail®.
http://windowslive.com/Tutorial/Hotmail/QuickAdd?ocid=TXT_TAGLM_WL_HM_Tutorial_QuickAdd_062009
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|