Towertalk
[Top] [All Lists]

Re: [TowerTalk] how to do coax on ring rotor?

To: "'StellarCAT'" <rxdesign@ssvecnet.com>, "'tower'" <towertalk@contesting.com>
Subject: Re: [TowerTalk] how to do coax on ring rotor?
From: "Tim Duffy" <k3lr@k3lr.com>
Date: Sun, 24 Mar 2019 15:26:25 -0400
List-post: <mailto:towertalk@contesting.com>
HI Gary

Have the loop below the boom works very well here. You have to have a safe 
climber in place for the installation and it check out  360 degrees while 
someone in the shack (linked by radios) operates the control box. Take measures 
to insure the coax can never get caught by the guy attachment hardware. The key 
to this is coming off the boom about 3 feet away from the tower face.

73
Tim K3LR



-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of 
StellarCAT
Sent: Sunday, March 24, 2019 1:56 PM
To: Tim Duffy; 'tower'
Subject: Re: [TowerTalk] how to do coax on ring rotor?

Thanks Tim ... as I wrote David direct -  it was a "DUH!" moment when I read 
his note - which was to use the truss support upright. I have been focusing 
too much on the actual antenna and the coax along the boom .... thinking 
loops around the tower and drapes etc.... I hadn't even considered the truss 
support. That should be pretty straight forward.

I do have a guy right below, within 3', so I'm reluctant to let it hang down 
directly from the boom .... although it looks like that is what you do Tim.


Gary
K9RX


-----Original Message----- 
From: Tim Duffy
Sent: Sunday, March 24, 2019 12:27 PM
To: 'StellarCAT' ; 'tower'
Subject: RE: [TowerTalk] how to do coax on ring rotor?

Hello Gary:

You can go to my website and see lots of photos of coax with ring rotors. 
There are 23 ring rotors here - so if you have questions after looking at 
the photos and videos - please email me and I will help

http://www.k3lr.com  look at contest photos and videos

73
Tim K3LR

-----Original Message-----
From: TowerTalk [mailto:towertalk-bounces@contesting.com] On Behalf Of 
StellarCAT
Sent: Sunday, March 24, 2019 12:00 PM
To: tower
Subject: [TowerTalk] how to do coax on ring rotor?

I’ve got two TIC ring rotors that are going up – hopefully this spring ... 
they’ll have 2 7 element 10’s on them ... (yeah, I know, 10M’s).... and I’m 
trying to figure out the best way to handle the coax coming off of the 
antennas. Both going up from the ring as well as going down. I need up 
because one of the rings will be mounted 4’ above a guy point so going down 
isn’t likely to be a solution.

Anyone done this already and gone through the trials and tribulations of 
getting it right?

You’re welcome to write direct to my ARRL email address or post here...

thanks – Gary, K9RX
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
<Prev in Thread] Current Thread [Next in Thread>