Take a few plates out of a lager value cap. That way it increases the
voltage.
73
Jim W7RY
-----Original Message-----
From: Jim Thomson
Sent: Saturday, August 19, 2017 11:48 AM
To: amps@contesting.com
Subject: [Amps] peak voltage rating for load cap
Date: Sat, 19 Aug 2017 12:07:14 +0200
From: Conrad PA5Y <g0ruz@g0ruz.com>
To: amps@contesting.com
Subject: [Amps] peak voltage rating for load cap
<Hello what is the rule of thumb for conservatively estimating the
<required ratings for a load capacitor when used with a mono band Pi-L
<tank circuit?
Anode voltage 2750V
Tube design RL = 2600 ohms
Q = 12
I have searched on the internet an I cannot find any really convincing
info, I have something that will stand 1200V but that is marginal and
will not survive a fault I expect.
Alternatively does anyone have a small vac variable around 40-60pF that
is around 3 inches/76mm? That will obviously do the job.
Also where can I buy a couple of Ohmite Z-50 chokes in Europe? Anyone
got one or two that they can spare?
Regards
Conrad PA5Y
### Ok, what band is this for ???? You wanted a 40-60 pf cap, for the
load cap of
a PI-L amp. The only thing I can think of is a 6M amp..and only if its a
PI-L, as you desired.
A simple PI net on 6m would require a bigger cap than 40-60 pf.
## The intermediate Z across the load cap on any PI-L can be anything you
want, like
from 60-1000 ohms. Typ its aprx 250-350 ohms. The peak V across a 300
ohm Z, is
obviously gonna be a lot more than a simple PI net load cap... which is at a
50 ohm point.
## If this is for a mono band 6M amp, as I suspect, and with a 2600 ohm
plate load Z, a better
option would be to use a L-PI, where some uh is place before the main PI
net. The added small uh
between the plate block cap..and the main C1 tune cap, forms a step down L
network.
End result is the main Pi can now be designed around a much lower plate load
Z...and increased harmonic
reduction. Typ, with lower plate load Zs, harmonic reduction increases.
## use GM3SEKs, free, excellent PI spreadsheet, he also has a PI-L...to
get the correct values for both
coils in the L-PI..and also the correct values for the C1 + C2 caps. Even
in the L-PI configuration,
the resulting ..transformed lower plate load Z will result in a higher C2
value..vs a normal plane PI.
Moot point, since the peak V across the load cap will be across a 50 ohm
point.
## peak V across a 50 ohm load cap, with 1.5 kw out = 389 V. Your 1200
V rated load cap is more than
up to the task, even with some SWR. I doubt you will be operating with a
3:1 swr on 6m, or any other band.
Square root of 3 = 1.73 Even with a 3:1 swr, peak V across the load cap
would then be 389 X 1.73 = 673 V peak.
Your 1200 V rated cap is still up to the task.
## If this is for a monoband 6M, a simple way to make the main tank coil is
to use copper strap, instead of copper tubing.
Copper strap, wound flat, has the advantage of conducting RF on BOTH sides
of the strap. Tubing only conducts
RF on the OUTSIDE of the tubing. IE: .375 inch wide strap is the same as
using .25 inch OD tubing.
Another advantage of strap coils, wound flat, is there is almost zero stray
C between
adjacent turns. Hence the spacing between turns can be very close, like
just a few mm. Strap coils are very easy to wind,
in any diameter, and the diameter can easily be reduced..or increased.
Strap coils are also easy to terminate, just punch a hole
at each end to terminate to the plate block caps at one end.... and the load
cap at the extreme other end. The aprx middle
of the coil is also easy to punch, and terminate on the main C1 Tune cap.
Strap can also be easily cut to any width you want.
10-15mm wide strap would work superb on 6M.
Typ you want to use strap that is aprx .024 to .032 inches thick. IE:
.6mm to .8mm thick. 1mm thick is also fine.
Its a lot easier to wind a strap coil... vs a tubing coil, with the tubing
being 6-10mm in diamter. The diameter of the strap
coil can be easily tweaked, on the fly, so the extreme ends end up right
where you want them.
## The L-PI configuration also has the advantage of being able to use a
lower loaded Q, vs a simple PI net....esp on
15-12-10-6M bands.
## whatever configuration you end up using, make sure to use 50 ohm coax
between the output of the PI, L-PI,
PI-L, or L-PI-L and the TR relay. The braid at each end has to be done
right, so you dont end up with any Z bumps, otherwise
you will end up with the load cap at a High Z point.
Jim VE7RF
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|