Kyle, It seems like you have checked everything. Here
is a few things to re-check.
Check MMTTY to see if you are setup correctly.
1. From Option menu, select 'setup mmtty'.
2. Goto 'TX' tab, goto the PTT Port item. You have
to have a comport selected and this comport MUST have
both the PTT and FSK wired on the same port. At least
it must have the FSK port.
3. Goto 'MISC' tab. If you were successful in the TX
tab of getting the comport, you will then select the
'COM-TXD' (FSK) item. If this is greyed out, then you
did something wrong. You can also select the item
above it, the 'Sound plus the CoM-TXD'. This way you
can here if the tones are coming in.
I would suggest that you go to the:
http://www.aa5au.com
webpage and go to the area that tell on how to setup
mmtty. It may help.
I do not know anything about the Yaesu.
Joe K0BX
--- wa4pgm@kinex.net wrote:
> So far no luck getting the 920 working in FSK mode.
> I've checked my
> Buxcomm interface with a ohm meter and it's showing
> a short when keyed,
> when I unkey the short goes away. This leaves me to
> believe my interface
> is good. Ed VP9GE has listened to my signal and it's
> only a carrier with
> no shift.
>
> Switch on back of rig is set for FSK.
>
> Rig Menu is setup:
> Mode - DATA/LSB
> U42 - Hi2125L
> U43 - Sft 170
> U44 - RES
>
> I don't find any other menu setting that might help,
> perhaps I've
> overlooked it.
>
> I tried different Volume/Recording Control settings
> so perhaps I've
> screwed something up there? At this point I don't
> know which way is up
> anymore. :)))
>
> Using MMTTY 1.65
>
> Doesn't look good at this point in hopes of
> operating NAQP, but I'll keep
> trying.
>
> THANKS EVERYONE!
> 73,
> Kyle
>
>
> > Kyle,
> >
> > 1. First, be sure that you are, in fact,
> supplying the FS keying
> > information
> > to the 920 before suspecting the rig. If you have
> an ohm meter, put it
> > across the leads that you are connecting to the
> FSK jack on the 920.
> > Depending on
> > what your sending, the meter should either show a
> short on keying or show
> > SOME fluctuation. If you are not getting any
> indication that the FSK
> > contacts
> > are being shorted for the duration of the mark
> tone, then you will have to
> > correct that problem -- which would be from the
> output of your computer or
> > your
> > Terminal Unit.
> >
> > 2. If you are getting an indication with a meter
> that the contacts are
> > being
> > supplied with a short when needed, then you need
> to be sure that you are,
> > in
> > fact, able to FSK the 920. Make a contact on
> phone. Tell the other
> > operator
> > that you will be sending a carrier and that when
> you touch a couple of
> > wires
> > together, the carrier frequency should shift
> slightly. For this test, it
> > would
> > be best to set the 920's FSK to USB. However, the
> other guy should be
> > able
> > to tune around and hear your carrier and detect a
> shift in it when you
> > touch
> > the wires together. Then, go back to SSB and
> listen to what he tells
> > you.
> >
> > If you are unable to shift the frequency in this
> way, that would indicate
> > that you still do not have the 920 set up
> correctly, or, it isn't working
> > right.
> >
> > 3. If you don't have a small VOM with you, get
> one at Radio Shack and
> > put
> > it in your travel kit. If you had one with you,
> you would be able to
> > easily
> > solve this problem.
> >
> > I'll be interested to see what you find.
> >
> > Good Luck!
> >
> > Mike
> > W0YR/4
> > _______________________________________________
> > RTTY mailing list
> > RTTY@contesting.com
> > http://lists.contesting.com/mailman/listinfo/rtty
> >
>
> _______________________________________________
> RTTY mailing list
> RTTY@contesting.com
> http://lists.contesting.com/mailman/listinfo/rtty
>
>
__________________________________
Do you Yahoo!?
Yahoo! Mail - 50x more storage than other providers!
http://promotions.yahoo.com/new_mail
_______________________________________________
RTTY mailing list
RTTY@contesting.com
http://lists.contesting.com/mailman/listinfo/rtty
|