Also running 2.056 and the Remote I/O works fine. I find that I have to
have the sub receiver's audio either muted or turned off so not to mix
with the desired audio on the main.
I am using a microHam microkeyer for my I/O and audio switching with
numerous programs.
Robb, NØRU
----- Original Message -----
From: "Larry Menzel" <retire@means.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, March 27, 2006 8:28 PM
Subject: Re: [TenTec] Orion Aux Audio output
> My apologies, guys, I'm still running 2.055. Intended to load .056 but
> haven't done so...may not if this is persistant.
>
> I do not see this with 2.055. Buck, maybe you want to revert and see if
> the
> problem persists.
>
> Larry, N0XB
>
> ----- Original Message -----
> From: "Barry Gross" <barry.n1eu@gmail.com>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Monday, March 27, 2006 7:20 PM
> Subject: Re: [TenTec] Orion Aux Audio output
>
>
>> On my v2.056 Orion, the aux I/O "line" outputs definitely vary (almost
>> linearly) with the main/sub af controls.
>>
>> 73,
>> Barry N1EU
>>
>> On 3/28/06, Larry Menzel <retire@means.net> wrote:
>>>
>>> Hi, Buck,
>>>
>>> Well, I"m running RTTY with 2.056, with no problem, using the AUX I/O.
>>> I
>>> set the volume to the program with the volume control for the soundcard.
>>> The front control has no function on the I/O. Are you sure you have the
>>> TX
>>> Audio Source in the SSB menu set to AUX and not MIC or BOTH? Then pull
>>> up
>>> in Windows START>All Programs>Accessories>Entertainment>Volume Control
>>> and
>>> make sure your LINE IN is enabled, or easier yet just click on the
>>> volume
>>> control in the lower right of your monitor. If you're hooked up
>>> correctly,
>>> LINE-IN will control the volume to the soundcard from the AUX OUT plug
>>> on
>>> the radio.
>>>
>>> It is possible that you're simply using the sound from the speaker
>>> through
>>> your microphone to drive the software, because the TX Audio Source is
>>> set
>>> to
>>> mic or both.
>>>
>>> Hope this helps...or call me at 952 212 2664
>>>
>>> Larry, N0XB
>>>
>>>
>>> ----- Original Message -----
>>> From: <K4IA@aol.com>
>>> To: <tentec@contesting.com>
>>> Cc: <ditsnbits@tentec.com>
>>> Sent: Sunday, March 26, 2006 11:27 PM
>>> Subject: [TenTec] Orion Aux Audio output
>>>
>>>
>>> >I have been trying to get back into digital modes and notice that the
>>> audio
>>> > output from the AUX I/O connector pin 4 seems to depend on the volume
>>> > control
>>> > instead of being a line out as described in the manual and as it
>>> operated
>>> > prior to ver 2.
>>> >
>>> > This is maddening because it means you have to turn up the volume and
>>> > listen
>>> > to the warbling. Before you could turn down the volume and just
>>> > watch
>>> > the
>>> > screen.
>>> >
>>> > Anyone else notice this?
>>> >
>>> > K4ia "Buck"
>>> > Fredericksburg, Virginia USA
>>> >
>>> > _______________________________________________
>>> > TenTec mailing list
>>> > TenTec@contesting.com
>>> > http://lists.contesting.com/mailman/listinfo/tentec
>>> >
>>> >
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|