Mike,
Thanks for responding to my question.
I bought the Omni VI + from Ten Tec a few years ago and the radio came with the
board installed.
There were some things going on in my life at that time and I didn’t have a
chance to check out the board or the rest of the radio. I know that sounds
silly, but that's what happened, anyway do you know if you can tell if the mod
has been done by looking at the board? There is a note in the manual stating if
the board came out of anything other than a 563 or 564 call the factory for
modification details. I guess I can shoot them off an e-mail and hope they
respond.
I was hoping that someone on here could answer my question.
73’s
Rich, WD6DOK
> On Mar 8, 2016, at 6:25 PM, Mike Bryce <prosolar@sssnet.com> wrote:
>
> silly question, but did this start to act up or did you buy a voice card and
> add it to the radio?
>
> There is a modification that needs to be done to the card if it came out of
> the paragon and into the Omni V/VI. I don’t recall what it was, but it was
> rather simple
>
> mike, wb8vge
>
>
> Mike, WB8VGE
> SunLight Energy Systems
> The Heathkit Shop
> http://www.theheathkitshop.com/ <http://www.theheathkitshop.com/>
> J e e p
> o|||||||o
>
> A man with one clock knows what time it is. A man with two clocks is never
> sure.
>
>
>
>> On Mar 8, 2016, at 4:45 PM, Froiseth Richard <rfwd6dok@centurylink.net>
>> wrote:
>>
>> I have an Omni VI + with the Voice Synthesizer Board #257 installed.
>> When I press the voice button on the front of the radio the voice announces
>> the following:
>>
>> 80m, 40m announces 29731 no matter where you are tuned.
>> 12m, 15m and 20m announces 429731 no matter where you are tuned.
>>
>> My understanding is the board should announce the freq. you are presently
>> tuned.
>>
>> Can anyone shed some light on this problem?
>>
>> 73’s
>> Rich, WD6DOK
>>
>>
>>
>>
>>
>>
>>
>>> On Mar 2, 2016, at 5:09 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:
>>>
>>> Don't use the 500hz and 250hz filters. Put an Inrad #762 600hz filter in
>>> the 1000hz slot: http://users.vnet.net/btippett/inrad_.htm
>>>
>>> 73, Barry N1EU
>>>
>>> On Wed, Mar 2, 2016 at 11:57 PM, Tim Wininger <ky5rtim@gmail.com> wrote:
>>>
>>>> Anyone have one or all of these filters excess to your needs. Looking for
>>>> the TT versions or Inrad versions.
>>>>
>>>> Thanks for any info,
>>>>
>>>> Tim , AB4B
>>>> Rogersville ,AL
>>>> 35652
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|