TenTec
[Top] [All Lists]

Re: [TenTec] Omni VI + Voice Synthesizer Board.

To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] Omni VI + Voice Synthesizer Board.
From: Froiseth Richard <Rfwd6dok@centurylink.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 9 Mar 2016 09:55:32 -0700
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
Carl,

Thanks for the info.
I wrote Ten Tec a note and they wont give out any info without a work order.
I use to be able to call and receive help on things like this, but I guess 
times have change.
Thanks again.

73’s
Rich, WD6DOK







> On Mar 9, 2016, at 9:50 AM, Carl Winkles <jcwinks@att.net> wrote:
> 
> Here is what Ten Tec told me years ago: "If there is a diode just to the left 
> of the MC74HC573 chip (third connection on the left edge of the card) place a 
> jumper across it. Depending on the model of the rig, there will be one diode, 
> two diodes or a jumper. The Omni series requires a jumper for proper readout. 
> '
> 
> I don't remember having any problem doing this, and I remember that it 
> worked.  Hope this helps. 
> 
> Carl, K4SEV
> 
> Enviado desde mi iPhone
> 
>> El mar 9, 2016, a las 1:56 AM, Froiseth Richard <Rfwd6dok@centurylink.net> 
>> escribió:
>> 
>> Mike,
>> 
>> Thanks for responding to my question.
>> I bought the Omni VI + from Ten Tec a few years ago and the radio came with 
>> the board installed.
>> There were some things going on in my life at that time and I didn’t have a 
>> chance to check out the board or the rest of the radio.  I know that sounds 
>> silly, but that's what happened, anyway do you know if you can tell if the 
>> mod has been done by looking at the board? There is a note in the manual 
>> stating if the board came out of anything other than a 563 or 564 call the 
>> factory for modification details.  I guess I can shoot them off an e-mail 
>> and hope they respond.
>> I was hoping that someone on here could answer my question.
>> 
>> 
>> 73’s
>> Rich, WD6DOK
>> 
>> 
>> 
>> 
>> 
>> 
>> 
>>> On Mar 8, 2016, at 6:25 PM, Mike Bryce <prosolar@sssnet.com> wrote:
>>> 
>>> silly question, but did this start to act up or did you buy a voice card 
>>> and add it to the radio?
>>> 
>>> There is a modification that needs to be done to the card if it came out of 
>>> the paragon and into the Omni V/VI. I don’t recall what it was, but it was 
>>> rather simple
>>> 
>>> mike, wb8vge
>>> 
>>> 
>>> Mike, WB8VGE
>>> SunLight Energy Systems
>>> The Heathkit Shop
>>> http://www.theheathkitshop.com/ <http://www.theheathkitshop.com/>
>>> J e e p
>>> o|||||||o 
>>> 
>>> A man with one clock knows what time it is. A man with two clocks is never 
>>> sure. 
>>> 
>>> 
>>> 
>>>> On Mar 8, 2016, at 4:45 PM, Froiseth Richard <rfwd6dok@centurylink.net> 
>>>> wrote:
>>>> 
>>>> I have an Omni VI + with the Voice Synthesizer Board #257 installed.
>>>> When I press the voice button on the front of the radio the voice 
>>>> announces the following:
>>>> 
>>>> 80m, 40m announces 29731 no matter where you are tuned.
>>>> 12m, 15m and 20m announces 429731 no matter where you are tuned.
>>>> 
>>>> My understanding is the board should announce the freq. you are presently 
>>>> tuned.
>>>> 
>>>> Can anyone shed some light on this problem?
>>>> 
>>>> 73’s
>>>> Rich, WD6DOK
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>> 
>>>>> On Mar 2, 2016, at 5:09 PM, Barry N1EU <barry.n1eu@gmail.com> wrote:
>>>>> 
>>>>> Don't use the 500hz and 250hz filters.  Put an Inrad #762 600hz filter in
>>>>> the 1000hz slot: http://users.vnet.net/btippett/inrad_.htm
>>>>> 
>>>>> 73, Barry N1EU
>>>>> 
>>>>>> On Wed, Mar 2, 2016 at 11:57 PM, Tim Wininger <ky5rtim@gmail.com> wrote:
>>>>>> 
>>>>>> Anyone have one or all of these filters excess to your needs. Looking for
>>>>>> the TT versions or Inrad versions.
>>>>>> 
>>>>>> Thanks for any info,
>>>>>> 
>>>>>> Tim , AB4B
>>>>>> Rogersville ,AL
>>>>>>    35652
>>>>>> _______________________________________________
>>>>>> TenTec mailing list
>>>>>> TenTec@contesting.com
>>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>>> _______________________________________________
>>>>> TenTec mailing list
>>>>> TenTec@contesting.com
>>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>>> 
>>>> _______________________________________________
>>>> TenTec mailing list
>>>> TenTec@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/tentec
>>> 
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>> 
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
<Prev in Thread] Current Thread [Next in Thread>