Well,now, I think someone aught to wear a HEADSET and then you don't hear
any damn clacking reed relays ...............
Walt K8CV Royal Oak, MI.
"Laissez les bons temps rouler"
----- Original Message -----
From: "Barry N1EU" <barry.n1eu@gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, November 14, 2011 8:22 AM
Subject: Re: [TenTec] Orion's break in
I only tried delaying one of the EXT TR relays and it made no
difference on the relay clacking - I didn't try delaying both of them.
On Mon, Nov 14, 2011 at 8:04 AM, Rick - DJ0IP / NJ0IP <Rick@dj0ip.de>
wrote:
Barry, if you delay those relays, they won't follow the cw keying and
they won't clack.
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com] On Behalf Of Barry N1EU
Sent: Monday, November 14, 2011 2:00 PM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Orion's break in
Right, but he's asking specifically about the audible relay clacking.
Barry N1EU
On Mon, Nov 14, 2011 at 7:51 AM, <d.e.warnick@comcast.net> wrote:
On the Orion II:
If you go to:
MENUS , TX, there is an EXT T/T Delay1 (or Delay 2) and that
"provides "hang time" for non-QSK linear amplifier"
If you go to:
MENUS, CW, There is a CW QSK Delay that "Allows the operator to slow the
QSK operation in CW transmit. A higher value represents more
transmit/receive delay between individual transmitgted CW characters.
This delay control also controls the deelay of the QSK amplifier keying
loops and the delay set for outputs at AMP KEY 1 and AMP KEY 2. The
default value is 20%."
The above is from my Orion II manual.
The part that is a bit vague to me is the default of 20% in the CW menu.
I should think that a delay of 0% would be true QSK, similar to my Omni
VI+, but I have no way to measure it. I'm sure that John Henry can teoll
us what value to set to have the same performance as the older Omni VI,
and Corsair II had.
Dave
WA3F
----- Original Message -----
From: "Barry N1EU" <barry.n1eu@gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Monday, November 14, 2011 6:17:09 AM
Subject: Re: [TenTec] Orion's break in
Two relays?
On Mon, Nov 14, 2011 at 10:22 AM, Rick - DJ0IP / NJ0IP <Rick@dj0ip.de>
wrote:
That makes no sense at all.
One would think that it adjusts the hang time of the Linear's own
relay, and therefore the Orion's internal relay would have to stop
clacking.
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com] On Behalf Of Barry N1EU
Sent: Monday, November 14, 2011 11:08 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Orion's break in
There IS an EXT T/R Delay setting in the TX Menu but it has no effect
on the keying relay clacking.
Barry N1EU
On Mon, Nov 14, 2011 at 7:56 AM, Rick - DJ0IP / NJ0IP <Rick@dj0ip.de>
wrote:
Guys, I may be wrong, but I seem to remember that there were TWO
adjustments; one for the relay and one for the RX recovery. It's been
over 5 years since I have owned an Orion, but I'm pretty certain it
was that way. In any case, it would have to be one of the items on the
TX menu.
73
Rick
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com] On Behalf Of Barry N1EU
Sent: Monday, November 14, 2011 1:40 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] Orion's break in
Correct Floyd, the CW delay makes the receiver audio quiet but does
nothing for the relay clacking in both the Orion and Orion II.
73, Barry N1EU
On Mon, Nov 14, 2011 at 12:11 AM, Floyd Sense <floyd@k8ac.net> wrote:
An interesting question. I wonder if the Orion and Orion 2 differ in
this respect. On my Orion 2, I can use the CW delay to achieve
semi-break-in, but I still hear the same relay clacking away. I
expected to hear the relay only at the beginning and end of a
transmission, but that's not the case - it still follows the keying,
although the receiver is properly muted for the delay set with the CW
delay function. So, maybe Toshimi's desire to eliminate the relay
noise
is not satisfied this way.
73, Floyd - K8AC
On 11/13/2011 5:56 PM, Barry N1EU wrote:
Menus - CW - CW QSK Delay
start with 25% and increase/decrease as necessary
73,
Barry N1EU
On Sun, Nov 13, 2011 at 10:39 PM, Rick - DJ0IP /
NJ0IP<Rick@dj0ip.de> wrote:
Hi Toshimi,
You can adjust the delay of the TR relay.
If you select a delay, then it is effectively semi BK and no longer
QSK.
This was added to the rig after the initial release so it probably
was not
in the manual.
Maybe someone who owns an Orion can jump in and tell you exactly
how to
adjust it. I have forgotten.
73
Rick, DJ0IP
-----Original Message-----
From: tentec-bounces@contesting.com
[mailto:tentec-bounces@contesting.com]
On Behalf Of Toshimi Horie
Sent: Sunday, November 13, 2011 11:32 PM
To: tentec@contesting.com
Subject: [TenTec] Orion's break in
Hi all. I am JE2UFF.
This month, I got the Orion of used one from US.
I just start operation with it. I can checked user manual, but not
found.
So please tell me for everyone.
The Orion has semi break in mode? I have other rig. That's japanese
one.
Normaly, japanese transceiver has two kind of break in operation
mode. It's
semi and full break in.
The Orion do the CW mode, each mores code can switch the relay. It
is very
noisy. Is this normal specs?
If it has semi break in mode then the relay can switch for start
and finish
of two times. Very quaiet.
Thanks all
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|