Ok,
I went and pulled my Eimac book down. I hadn't earlier where it was at as I
couldn't hardly reach it from my wheelchair.
I guess I need shorter book shelves : ) Anyhow, this one does have the Class
AB2 listed as below from page 2. Strangely, this one does not mention class B
like the pdf did.
Quote;
Radio frequency Linear Amplifier
Cathode driven
Class AB2
Maximum Ratings:
DC plate voltage 4000 Vdc
DC plate current 0.4 ampere
Plate dissapation 500 watts
Grid dissapation 20 watts
Typical operation (Frequencies to 110 MHz)
Class AB2, peak envelope or modulation crest conditions
>>(Here I'm going to show the maximum plate voltage they show of 3500 Vdc)
Plate voltage 3500 Vdc
Cathode voltage +15 (+10 at 3000 and 0 at 2500)
Zero signal plate current 53 mA
Single-tone plate current, CW 3/4 400 mA
Two-tone plate current 262 mA
Single-tone grid current 108 mA
Two-tone grid current 58 mA
Single-tone power input 1400 W
Useful output power, CW or PEP 890 W
Resonant load impedance 5000 ohms
Intermodulation distortion products;
3rd order -40 dB
5th order -45 dB
Single-tone current for 3500 Vdc operation may reach this value during short
periods of circuit adjustment only.
IMD products are referenced against one tone of a two equal tone signal.
Currents listed corrospond to SSB, or "two-tone" average current at peak of
signal envelope.
End Quote.
Best,
Will
*********** REPLY SEPARATOR ***********
On 6/27/06 at 1:31 PM R L Measures wrote:
>On Jun 27, 2006, at 6:51 AM, Will Matney wrote:
>
>> Rich,
>>
>> It was the same thing as they printed it I was refering, or to me
>> it was as I wrote it. It was Eimacs maximum rating at 1 KW input, G-
>> G, class B RF amp showing it's minimum distortion, or the way they
>> have it listed.
>
>I have seen no info from Eimac on Class B for the 3-500Z.
>>
>> Best,
>>
>> Will
>>
>> *********** REPLY SEPARATOR ***********
>>
>> On 6/27/06 at 6:19 AM R L Measures wrote:
>>
>>> On Jun 27, 2006, at 2:46 AM, Tom W8JI wrote:
>>>
>>>>> They can be used on up in current, say for pulse circuits
>>>>> and RF heating. The 400 mA is the maximum plate current at
>>>>> single tone for minimum distortion. That's for 600 watts
>>>>> PEP useful power each. That's listed in the tables on page
>>>>> 2 or 3 under a class B RF amp.
>>>>
>>>> Will,
>>>>
>>>> Where did you get the idea 400mA is a "minimum distortion"
>>>> condition?
>>>
>>> Good point, Tom. Will should have said something like: for minimal
>>> distortion, the max rated anode-I is 400mA.
>>>>
>>>> 73 Tom
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> Amps mailing list
>>>> Amps@contesting.com
>>>> http://lists.contesting.com/mailman/listinfo/amps
>>>>
>>>
>>> R L MEASURES, AG6K. 805-386-3734
>>> r@somis.org
>>
>>
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>
>R L MEASURES, AG6K. 805-386-3734
>r@somis.org
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|