Amps
[Top] [All Lists]

[Amps] The Carl and Jim Show

To: <amps@contesting.com>
Subject: [Amps] The Carl and Jim Show
From: "Jim Thomson" <jim.thom@telus.net>
Date: Thu, 6 Jun 2013 07:47:11 -0700
List-post: <amps@contesting.com">mailto:amps@contesting.com>
Date: Thu, 6 Jun 2013 09:06:16 -0400
From: "Carl" <km1h@jeremy.mv.com>
To: <jim@audiosystemsgroup.com>, <amps@contesting.com>
Subject: Re: [Amps] The Carl and Jim Show

Well at least JimVE7RF and I are still friends and we simply enjoy the 
banter but on here there are those who get their knickers in a knot.

In your case you dont have 50 years experience but like to use others 
information and call it your own and act as if ferrites, common mode/RFI/TVI 
suppression is your own discovery. Sorry to dissapoint you but it was 
already old when I was introduced to it in the 70's.

Carl
KM1H

## Beware of using small size coax, like RG-303 teflon types and also RG-58U, 
when
a lot of turns are used on stacked type 31/ 43   2.4 inch OD cores. You can 
easily get 
parasitic arcing between adjacent turns.   That happened with a buddy who tried 
that
config, and placing it BEFORE a hb T type tuner, configured for balanced  line. 
He also
tried using 8 x type 43 cores,  4 on each side..and cooked the cores.   Jay at  
array solutions
warned me about using too many turns of small coax on XXX cores,  even if the 
choke is
at the feedpoint of a balanced ant..... you can get arcing between the last two 
turns, at least with
serious qro.   

##  It’s a dumb place to try an insert a choke. W8JI was right, you need at 
least a 50 k choke
Z if you try an put the choke in front of a T type tuner. Problem is, even when 
configured for
balanced operation, the T type tuner is still not balanced, not even close.   
The fix was to reconfigure
the T  type tuner back to un-balanced operation..... then use coax on output 
side of the tuner
to a 1:4  balun, then the  450 ohm line. 

##  what else that works is a balanced L  type tuner, like you see on rich 
measures site.  That
type of tuner is truly balanced....and a choke can be inserted  before the 
tuner.  Dunno if Rich
cooked it up or not, but I see that at least two manufacturers  have ripped off 
the idea. 

##  as far as Z  going up to the square of N turns of coax through ferrite 
cores, nothing new there. 
About the only new thing is type 31.   Dunno if type 77 is still available or 
not. 

##  I find it amusing that when reading k9YC  tutorials,  power point 
presentations, and everything else
he has available, that he always avoids feedline lengths of  1/4 wave and 3/4 
wave, and 5/4  etc. 
The feed point  Z is sky high at those lengths.  But these are physical 
lengths..and not electrical.  Then
you gotta shorten by 2%, to factor the stray C between coax and yagi boom.   
The concept works good too,
but so far has only be used with yagis  on top of a steel tower.  Braid of coax 
 bonded to mast or top of tower,
then the   1/4, 3/4 wave of coax  run from remote switch box to each yagi.   
Then you don’t need a choke
balun at the feedpoint.  A clamp on RF ammeter run up and down the main coax 
will verify the effect.     

##  as far as the dreaded pin 1 problem on commercial audio gear when balanced 
inputs are used, I have yet to
see any gear with a pin 1 problem.   It has to be really old gear to have a pin 
1 problem.   Nobody would be stupid
enough to build gear with pin 1 problems these days, the gear would be sent 
back asap. 

Jim  VE7RF

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
<Prev in Thread] Current Thread [Next in Thread>