TenTec
[Top] [All Lists]

Re: [TenTec] Ham Radio Deluxe

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] Ham Radio Deluxe
From: "jack" <jfriend31@comcast.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Tue, 27 Jan 2009 15:18:20 -0700
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
try them both. the one that works is the one you want!
i am using COM1 for the ORION and LOGic8. COM3 is for MixW to send CW to a 
switch that keys the ORION.
jack ak7o


----- Original Message ----- 
From: "DW Holtman" <tubestuff@comcast.net>
To: <ray_2098@yahoo.com>; "Discussion of Ten-Tec Equipment" 
<tentec@contesting.com>
Sent: Tuesday, January 27, 2009 11:31 AM
Subject: Re: [TenTec] Ham Radio Deluxe


> Dell,
>
> Thank you for taking the time to send the setup information. However, it
> still does not communicate. I did a master reset of the Omni with no 
> change?
>
> I have a couple of additional questions. The PCI serial card has two DB9
> female connectors on it. Looking at the hardware information on Windows XP
> it says they are COM-5 and Com-6. How do I tell which is which? I.E.: is 
> the
> cable hooked up to 5 or 6?
>
> In TRX the setup manager (Parameters) on the right side there is a TRX 
> Port
> 1 with a pull down box with all of the possible Com 5,6 etc connections.
> Below this is another pull down box with Com 5, 6 etc. Which one is for 
> the
> communication port the cable is hooked up to my computer? What is the 
> other
> one for?
>
> Thank you again for your help.
>
> Best,
> DW Holtman
> WB7SSN
>
> ----- Original Message ----- 
> From: "Dell Ray" <ray_2098@yahoo.com>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Monday, January 26, 2009 8:09 PM
> Subject: Re: [TenTec] Ham Radio Deluxe
>
>
>> Hi Dyke
>>  I don't remember If you have a manual, And if you checked the settings
>> according to the manual. When I ran TRX the first time The only thing i
>> had to do was select the rig then pick my baud rate and comm port.
>> Everthing else I left as default.  I have Addr.=04,  Ctrl=E0,  mem=90,
>> Stop bits=2,  TRX Port1=Com 4,  CAT speed=19200,   dual control=checked,
>> RTS Enable=checked,  DTR enabled=checked,  PTT=CAT,  TX Interrupt=DSR,.
>>  I use a over the counter Belkin cable from computer to rig. I am using
>> vista 64 on a duel Intel CPU. I also had to buy a serial card but mine 
>> was
>> a Rosewell. Just be sure the rig is the same settings as Comp.
>>  Also you might try a master rest of the Rig. Might have a brain cramp.
>>
>>
>> Dell R Smith
>> Prosser,Wa
>> KI7XD DN-06
>> OMNI VI Opt1
>>
>>
>> --- On Mon, 1/26/09, DW Holtman <tubestuff@comcast.net> wrote:
>>
>>> From: DW Holtman <tubestuff@comcast.net>
>>> Subject: Re: [TenTec] Ham Radio Deluxe
>>> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>>> Date: Monday, January 26, 2009, 6:40 PM
>>> Hello,
>>>
>>> I installed a PCI serial card from byterunner. Windows
>>> under XT under
>>> Hardware information, tells me that it is properly
>>> installed and working. I
>>> triple checked the wiring in the cable. Tried Hyperterminal
>>> as suggested in
>>> the Ten Tec troubleshooting document. Not too sure that I
>>> had Hyperterminal
>>> was set up correctly? Still no luck, no communication. I
>>> tried two software
>>> packages, HRD and TRX.
>>>
>>> Any suggestions on where I should go from here?
>>>
>>> Thank you,
>>> DW Holtman
>>> WB7SSN
>>>
>>> ----- Original Message ----- 
>>> From: "Mike, K9UW" <k9uw@wi-net.com>
>>> To: "Discussion of Ten-Tec Equipment"
>>> <tentec@contesting.com>
>>> Sent: Sunday, January 18, 2009 6:05 PM
>>> Subject: Re: [TenTec] Ham Radio Deluxe
>>>
>>>
>>> > DW, I've used PCI serial cards from Byterunner on
>>> several occasions with
>>> > excellent results.  They're cheaper than most
>>> places as well.  Their
>>> > telephone rep told me, last time I called, that Hams
>>> were regular
>>> > customers.
>>> >
>>> >
>>> <http://www.byterunner.com/byterunner/category=2+Serial+(RS-232)+PCI-bus+cards/exact_match=exact>
>>> >
>>> >
>>> > 73, de Mike, K9UW
>>> > Amherst, WI
>>> >
>>> > DW Holtman wrote:
>>> >> Tim,
>>> >>
>>> >> I will check tomorrow and see if  I can find a
>>> Serial Port PCI  Card. Is
>>> >> there any drivers etc required, or is a Serial
>>> Card plug and go.
>>> >>
>>> >> Thank you again,
>>> >> DW Holtman
>>> >> WB7SSN
>>> >>
>>> >>
>>> >>
>>> > _______________________________________________
>>> > TenTec mailing list
>>> > TenTec@contesting.com
>>> > http://lists.contesting.com/mailman/listinfo/tentec
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>