Karlnet
[Top] [All Lists]

RE: [Karlnet] limiting bandwidth

To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
Subject: RE: [Karlnet] limiting bandwidth
From: "Eric Meth" <emeth@iescomm.on.ca>
Reply-to: Karlnet Mailing List <karlnet@WISPNotes.com>
Date: Wed, 9 Apr 2003 17:52:11 -0400
List-post: <mailto:karlnet@WISPNotes.com>
Chris. In version 3.88 it worked properly, you could set the rates
individually. Since then, setting the MaxTxRate sets both. Asymmetrical does
not work. Karlnet suggests setting the transmit rate on the AccessPoint
(version 4.31) then setting the CPE. Unfortunately the WaveWireless Firmware
is still at 4.02 where independent setting do not work. Use this flaw to
your advantage, sell symmetrical service!!! If you want to limit upload, do
it with a MikroTik router at the point where your wireless heads to the
internet directly. (One man's solution) Regards, Eric

-----Original Message-----
From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]On Behalf Of Chris Conn
Sent: Wednesday, April 09, 2003 5:11 PM
To: Karlnet Mailing List
Subject: Re: [Karlnet] limiting bandwidth


Eric Meth wrote:
> You can set the upload rate limit on the transmitter. The download rate is
> set by specifing the rate on the ethernet interface.
>

Hello,

Has anyone tried this recently?  I am trying to set up an asymmetrical
system
where customers upload at a fraction of their download speed and so far to
no
avail.  Setting a rate on the Ethernet will limit the customer's download
speed, however specifying a rate on the 802.11b interface seems to set that
rate for download AND upload.  I have tested this just yesterday on 3.88,
4.02
and 4.31 versions.  If my memory serves me correctly, it has however been
possible in the past to independantly configure rates on the various
interfaces.

Chris


>
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
> [mailto:karlnet-bounces@WISPNotes.com]On Behalf Of LaRoy McCann
> Sent: Wednesday, April 09, 2003 4:58 PM
> To: karlnet@WISPNotes.com
> Subject: [Karlnet] limiting bandwidth
>
>
> How do you limit a user to a certain bandwidth?  The only setting I can
> find on the karlnet firmware is Max Tx Rate in Kbits / Sec.  Actually this
> is a speedlan 8000 series box, but it uses the karlnet firmware.
>
> If this sets only the Tx side, then you are only limiting the upload speed
> and  not the download speed.  I want to limit the speed that a user
> downloads data to their computer.
>
> I know the connections are sold based on the speed that a user wants to
pay
> for, but just am not sure exactly how to limit that.
>
> If the wireless link will not do that then what is everyone else doing to
> limit a user to a certain bandwidth.
>
> I guess I could setup a linux box and use iptables to limit each user.
>
> Sorry if this issue has been beat to death before.
>
> Thanks
> LaRoy McCann
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet


_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet


<Prev in Thread] Current Thread [Next in Thread>